Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

72-hour field station plan: sizing LiFePO4, taming generator noise, and grounding choices. What would you change?

ci_cover.jpg

I'm sketching a baseline power and antenna plan for a 72-hour field deployment and want to see where it falls short. The scenario is a two-operator station in a tent: one HF rig (100 W class) and one VHF/UHF mobile (50 W class) on a repeater and simplex, plus a laptop for logging and a few LED lights. Assume it's an EMCOMM-style activation where the station has to keep running even if something fails. Nobody is on mains power.

The plan so far has the following parts.

Primary power is a 100 Ah LiFePO4 battery feeding a fused distribution block with Anderson Powerpole outlets. Each branch gets its own fuse: HF rig, VHF/UHF rig, a general-purpose accessory branch, and a separate lighting branch. A 200 W folding solar panel with an MPPT controller handles daytime charging. An inverter generator is the backup and recharge source. It would sit well downwind of the tent, on a long cord, with a CO alarm inside the shelter.

Antennas are a 10 m (about 33 ft) telescoping fiberglass mast with a multiband EFHW or a center-fed dipole on a choke, and a separate J-pole or small vertical for VHF/UHF on its own short mast. Coax runs are RG-8X-class for HF and something lower loss for the VHF/UHF run. Grounding is a single ground rod at the station entry point, with everything bonded to it.

The questions I'd like input on:

1. Does 100 Ah make sense for 72 hours, or is the generator the real plan and the battery just a buffer?

2. What's the best way to find out whether the MPPT controller or the generator is the noise source on HF before the deployment, not during it?

3. Is the single ground rod doing anything useful for RF, or is it mostly a safety and static measure?

4. What would you add to the setup and teardown checklists that people commonly forget?

  • Replies 2
  • Views 54
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On sizing, work it out in watt-hours instead of guessing. A 100 Ah LiFePO4 battery is roughly 1,280 Wh nominal (12.8 V × 100 Ah), and you can plan on using maybe 80–90% of that. Receive current for a typical HF rig is only a couple of amps. A 100 W SSB transmitter might pull 20 A or more on peaks, but the average is much lower because of voice duty cycle. Digital modes, FM at full power, and long net-control stretches change that math a lot. Build a table with receive hours, transmit hours at each power level, laptop draw, and lighting, then add a margin. Many people find 100 Ah is comfortable for a day or so of moderate operation. At 72 hours it works with solar topping it off, or with a generator run on a schedule.

For the generator, running it a couple of hours to recharge, then shutting it down, is usually quieter in every sense than running it continuously. You also get long periods of clean receive. Check what charger or converter you're using to put that energy into the battery. A cheap switching charger can be a worse noise source than the generator itself. Give the LiFePO4 a charger with the correct profile, or use the battery's recommended input. Also remember that many LiFePO4 batteries shouldn't be charged below freezing unless they have low-temperature protection, and a BMS can cut off abruptly on overcurrent or low voltage. A radio that suddenly loses power mid-net is something to plan around, so keep a clearly labeled second power source for the most critical radio.

For noise isolation, don't wait for deployment day. Set up the full system in a yard or park and use a battery-powered receiver to check each piece. Turn everything off, note the baseline noise floor on the bands you care about, then add one item at a time: the MPPT controller, the laptop and its charger, the LED lights, the generator, and the generator charger. Cheap LED lanterns and some solar controllers can be surprisingly loud on HF. The usual fixes are physical distance, short twisted DC leads, ferrite cores on power and USB cables, and keeping the noisy gear and its wiring away from the antenna and feedline. Some generators have an eco or idle-throttle mode that varies the load response, and it's worth testing whether it changes noise or voltage stability.

On safety, keep the generator well away from the tent, with the exhaust pointed away, and refuel only when it's off and cool. Don't skip the CO alarm. Follow the generator manual for any grounding instructions, because the right approach depends on the model and how the AC is distributed.

  • Moderators

On question 3, treat safety grounding, lightning, and RF grounding as separate concerns. A ground rod at the station is fine for bonding equipment together and can help bleed off static, but it won't turn a dipole into a good antenna, and it won't make a field station safe in a thunderstorm. If lightning is nearby, the correct move is to take down the antenna, disconnect feedlines, and get people into a proper shelter, not to rely on a rod. Bond the radios, distribution block, and any metal mast or equipment frames together with short, heavy leads so there's no voltage difference between them.

For most field antennas, the RF performance issue is common-mode current on the coax. A dipole or EFHW often works better and quieter with a good choke at the feedpoint. A common approach is a stack of ferrite beads or several turns of coax on a suitable core (mix 31 is common for HF). An EFHW also needs its matching unit and a counterpoise, and it's worth checking SWR and noise with the coax draped in different ways, since a feedline that's part of the antenna will also pick up noise from the shack.

Coax losses are worth checking against your actual runs. At HF, even smaller cable like RG-8X is fine for short runs. At 2 m and 70 cm, loss climbs quickly with length. A long run of thin cable can eat a big chunk of a 50 W signal and hurt receive just as much, so put the VHF/UHF antenna as close to the radio as the situation allows, or use lower-loss cable if you need height. Add drip loops, strain relief at the mast and at the radio, weatherproofed connections, and a cable ramp where people walk. Label both ends of every cable.

The mast needs its own checklist: check the wind rating, guy it at the points the manufacturer specifies, stake or ballast the base properly, flag the guy lines, and put the mast where its fall zone doesn't reach any power line or the tent. If there's any doubt about wind, plan to lower it.

For the setup list, I'd add the items people tend to forget: a written power plan and fuse map taped inside the tent, spare fuses and Powerpole contacts with a crimper, a multimeter, an antenna analyzer, a battery-powered receiver for noise checks, and a printed frequency plan that matches whatever the served agency expects. For teardown: shut down in order (transmit gear off, then distribution, then battery), photograph or note the connections before disassembly, coil coax loosely, check for damaged connectors before they go back in storage, recharge and cycle batteries soon after, and refill or label the fuel. After the event, jot down what failed or got noisy so the next deployment improves on it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.