Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

SSB audio that gets through: mic gain, ALC, processing and filters, from clean local audio to weak-signal DX

ci_cover.jpg

Most SSB audio problems come from the same few settings: mic gain too high, too much compression, and a transmit bandwidth that wastes power on frequencies that don't help intelligibility. This thread is meant for comparing approaches, so here's a baseline to argue with.

Sideband choice. By convention, LSB is used below 10 MHz (160, 80 and 40 m) and USB above it (20 m through 10 m). On 60 m, USB is the norm where channelized operation applies. The reason is historical, but it keeps everyone's receive filters and tuning habits aligned. If you're on the wrong sideband, a station may still be readable, but it will sound inverted and be harder to tune.

Microphone and placement. The mic matters less than consistency. A modest dynamic headset or desk mic used at a steady distance, usually a few centimetres to a hand's width from the mouth and slightly off-axis to reduce plosives, will often beat an expensive mic used carelessly. Check that the mic type matches what the rig expects, since some radios supply bias voltage for electret elements and others don't. Hard, bare walls and a nearby monitor or desk surface add reflections that make speech sound boxy, and a compressor will only make that more obvious.

Mic gain and ALC. Set mic gain with the processor off first. Speak at normal volume and adjust so voice peaks just touch the ALC range your manual recommends, without pinning it. ALC is a protection circuit, not a loudness control. If the ALC is working hard, the signal is being clipped and distorted in a way that widens it. Watch the ALC meter, not the power meter, and keep any external amplifier's ALC feedback in mind if you use one.

Processor and compression. Compression raises average power relative to peak power, which can help a weak signal stand out. It also raises background noise and sibilance, and heavy settings can sound strained. RF clipping, where available, can add more punch but also more distortion products. Start with the processor off, then add a small amount, and stop when the meter shows a modest compression level. Beyond that, clarity usually drops faster than loudness gains.

EQ and bandwidth. A transmit bandwidth of roughly 2.4 to 2.7 kHz is a common compromise. Many operators cut the lows below about 200 to 300 Hz and gently emphasize the 1.5 to 3 kHz range for intelligibility. Wider settings can sound more natural during a rag chew on a quiet band, but they take more spectrum and don't help when the band is crowded.

Monitoring. Use headphones to avoid feedback. Keep in mind that the monitor function in many rigs reflects audio at an early stage rather than the final RF signal, so it won't reveal splatter from an overdriven amplifier. An SDR, a second receiver or a remote receiver is a better check.

What's your order of operations when setting up a new mic or rig, and what do you rely on to judge your audio objectively?

  • Replies 2
  • Views 36
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One thing I'd stress is to adjust in a fixed order and change one variable at a time. Mic gain first, then ALC, then processor, then EQ. If you tweak all four at once, you can't tell what caused the improvement or the harshness.

For judging audio, a recording is more honest than your own ears. Record a short test call, then listen on a plain speaker rather than the monitor, and compare processor off, low and medium. Most people find the low setting best for copy: it's louder than off but without the breathy, pumped sound of heavy compression. Also check your lows. Boomy bass on a transmit EQ eats power but contributes almost nothing to being understood, especially through a 2.4 kHz receive filter on the other end.

On ALC, a common mistake is to turn up mic gain until the power meter looks good. If the ALC reads high, you're adding distortion and widening the signal, and a clean amp-driven signal at slightly lower power is usually easier to copy than a clipped one at higher power. If your radio has a compression meter and a separate ALC meter, watch both: compression working while ALC stays near zero is generally the target.

  • Administrators

For weak stations and DX, the receive side matters as much as the transmit side. A 2.4 kHz filter is a good default, but narrowing to about 1.8 to 2.2 kHz can reduce noise and adjacent splatter when the band is busy. If it's still hard to copy, try the passband tuning or IF shift to move away from the interference before reaching for heavy noise reduction, which can leave speech sounding watery. Using a notch for a carrier is often better than narrowing further. AGC speed also matters: a fast or medium setting can keep a strong neighbor from making the weak station pump in and out.

On the transmit side, speak slightly slower than normal, give your callsign clearly, and use standard phonetics. Calling in a DX pileup, short and precise beats loud and long. If the DX is working split, put your transmit VFO where they are listening, check that it's clear, and don't transmit on their frequency. Also listen for a while to learn their pattern before calling. Keep the processor moderate, since a clean, intelligible signal is more useful than an extra few dB of average power that comes with a harsh sound.

If you have a second receiver or SDR, look at your own signal occasionally to check bandwidth and splatter, especially with a processor and an amplifier in the chain.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.