Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Radio mods that are worth doing (and the ones that cause trouble): expanded RX, filters, TCXO, power, fans, and staying legal

ci_cover.jpg

Opening a thread on radio modifications, since the topic mixes good upgrades with ones that create problems. Here is a framework for sorting them, with room for everyone to add or disagree.

1. Expanded receive is not the same as expanded transmit. Many handhelds and mobiles can be unlocked in firmware or by a diode or jumper change so they receive well outside the ham bands. That is useful for weather, aviation monitoring, public service and scanning. The catch is that the front end was designed for the band the radio was sold for. Outside it you may see reduced sensitivity, images, and intermod or overload from nearby broadcast FM and pagers. A wideband receiver in a strong RF environment often benefits more from an FM broadcast notch filter or a band-specific bandpass filter than from any internal change.

2. MARS and CAP mods. These are often described online as just enabling TX on certain frequencies. Authorization is the actual requirement. MARS and CAP operate on government-assigned channels under their own programs, and you need to be an approved member, use the frequencies you are assigned, and follow the program's equipment and operating guidance. Having a radio that can transmit there does not give you permission to. Ask your program's communications officer what is acceptable for your radio. Also keep in mind that a radio opened up for out-of-band transmit can be a problem if it ends up used on an unauthorized service.

3. TCXO and frequency stability. A TCXO is a good upgrade for HF rigs and for weak-signal or digital work where frequency drift matters, such as FT8, WSPR, and narrowband modes. On VHF/UHF FM it matters less, since the channels are wide enough that modest drift usually does not hurt. For a rig where the manufacturer offers an optional TCXO, use that rather than improvising. After installing one, calibrate against a known reference such as a frequency counter with a good timebase, a GPS-disciplined source, or WWV, because a TCXO that has not been aligned to a reference is not necessarily better than the stock oscillator.

4. Filters. Roofing filters, narrow IF filters, and external preselectors can help much more than adding gain. If the noise floor is high, extra gain just amplifies what you already have. If the problem is strong adjacent signals, filtering before the first mixer is where improvement comes from. For handhelds, a notch for the FM broadcast band and a duplexer or cavity filter at repeater sites address overload far better than swapping antennas at random.

5. Audio upgrades. Transmit audio is mostly about not overdriving the radio. Watch ALC on HF and deviation on FM. Excessive mic gain and heavy processing produce splatter and a harsh sound, not extra range. On the receive side, an external speaker with a bit of damping and some DSP noise reduction often does more than internal changes. For 9600-baud packet or other data modes, many radios need a data port or discriminator tap, and the mod should be done with the right level checks, not guessed at.

6. Firmware. Update from the manufacturer's official source, back up memory or codeplug first, and use stable power during the flash because a battery dropping out mid-update can brick a radio. Third-party or open-source firmware can add features, but it may change power, deviation, and spurious behavior, so check it on a test setup before using it on the air.

7. Cooling fans. Fans make sense for high duty cycle use, especially digital modes, data transmissions, and compact rigs on summer days. Use a fan that is thermostat-controlled or at least separately fused, mount it so it moves air across the heatsink rather than just stirring the case, and keep fan wiring tidy. Cheap brushless fans can radiate hash into the receiver, so use ferrites and consider a linear or filtered supply for the fan.

8. Battery and power. A sagging supply is a common reason for low output and distorted audio. For 12 V gear, check what the radio actually sees at the connector under transmit load. LiFePO4 packs are popular because they are stable and nearly match the radio's voltage window, but check the voltage range against the radio's rating. Whatever the chemistry, fuse close to the battery, use Powerpoles or equivalent properly crimped, and use proper wire gauge. For handhelds, battery eliminators and larger packs need regulation and protection, and the output should not exceed the radio's rated input.

9. RF and noise reduction. Start by isolating the noise source: run on a battery, turn off breakers one at a time, and unplug likely culprits such as switching supplies, LED lighting, chargers and solar controllers. Common-mode chokes at the feedline, on DC leads, and on USB or audio cables solve a lot. Use a choke material suited to the frequency range, since mix 31 and mix 43 behave differently. A modification that adds a switching regulator inside the rig can create the very noise you are trying to remove.

10. Legal use of modified rigs. Rules vary by country, so check yours. In the US, amateur radios generally do not need equipment certification for use on amateur bands, but you must follow the Part 97 technical rules, including spurious emission limits, and you must be licensed for what you transmit. Services such as GMRS, FRS, and commercial land mobile require certified equipment, so modifying a radio used there can make it noncompliant. Transmitting outside the amateur bands is only acceptable if you are authorized for that service and the radio is permitted for it. Receive-only modification is generally a much lower-risk area, though some jurisdictions restrict what you may listen to or do with the information.

A safe approach to any mod: keep it reversible, document what you changed, use ESD precautions, keep stock parts, and verify results with instruments. A power meter, dummy load, and ideally a spectrum analyzer or service monitor will tell you far more than signal reports. Check harmonics and deviation after any change that touches the transmit chain.

Which upgrades have given you the most real-world improvement per dollar, and where have you seen mods make things worse?

  • Replies 2
  • Views 38
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Good list. I would move power and noise to the top, because those fix problems people blame on the radio. A rig that appears to have a weak receiver is often sitting next to a cheap USB charger or a switching supply, and a transmitter that seems underpowered is often fed through thin wire or a bad connector. Measure voltage at the radio during TX before buying anything.

On expanded receive: the unlock is the easy part. Keep in mind that when you open up a handheld's coverage, the squelch and AGC behave differently on bands it was not designed for, and the specs on sensitivity no longer apply. A cheap bandpass or notch filter in line often does more good than the unlock itself, especially in a city with strong FM broadcast and paging transmitters.

One more caution on fans: a fan that cuts out while the rig is on makes things worse than no fan, because people start running higher duty cycles. If you add one, make sure the heatsink design actually benefits from airflow and that the fan has some failure indication.

  • Administrators

Agree on authorization for MARS and CAP, and I would go further: the mod discussion often skips the part where the program may specify certain radios, programming procedures, or frequency use. Check with your own coordinator first, because the rules differ between programs and can change. Treat any forum list of the right mod as a starting point, not permission.

For firmware, one habit that saves headaches is to save the codeplug, read the radio's current settings, and write down the version before you flash. If you use third-party firmware, test the output on a dummy load with a meter and a second receiver or SDR to look at spurs, because features can be added without the same RF tuning the manufacturer did.

For TCXO work, the calibration step gets skipped a lot. If the frequency is not measured against something reliable afterward, you do not know whether the mod helped. A GPS-referenced counter or even WWV on a frequency your rig can receive is enough to tell you whether you are close. Also check the radio's own service manual for the intended reference adjustment point before you start poking at trimmer capacitors.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.