Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Small lot, HOA, 80m–10m: how to rank EFHW, OCFD, doublet, inverted V and loaded verticals by efficiency rather than SWR

ci_cover.jpg

A common setup question: a 50 x 100 ft lot, an HOA that bans visible towers and beams, a 100 W rig, and a wish for 40m through 10m with some 80m if possible. The usual answers are an EFHW, an OCFD, a G5RV, a doublet on ladder line, or a vertical. They get compared by SWR, which is the weakest way to compare them. Here is a framework for ranking them, and I'd like to hear where people disagree.

1. SWR tells you about the match, not the radiation. A dummy load gives a perfect 1:1 and radiates nothing. What matters is how much power ends up in the far field. That is feedline loss (including mismatch loss), loss in matching components such as transformers, chokes and tuners, ground loss for verticals, and conductor and capacitor loss for small loops. Antenna height and surroundings then set the takeoff angle.

2. Feedline loss climbs with SWR. Matched loss for common coax is roughly 1 dB per 100 ft on 20m for RG-58-class cable and well under that for RG-213-class cable. Loss at high SWR is considerably worse, and it rises with frequency. A 50 ft run of decent coax with a modest SWR is fine. A long run of thin coax at 10m with a 5:1 SWR is not. Ladder line is the reverse: it stays low-loss at high SWR, which is why a doublet plus a tuner works well even when the antenna impedance is awkward.

3. Common-mode current is the hidden variable. Many "mystery" problems come from RF on the coax shield: RF in the shack, a different SWR when you move the cable, and noise pickup on receive. Put a proper choke (a 1:1 current balun, or ferrite beads or a coil of coax made with a suitable core) where the feedline leaves the antenna. An EFHW is a special case. The 49:1 or 64:1 transformer feeds a very high impedance end, and the coax shield acts as part of the counterpoise unless you manage it. A choke a short distance down the coax is the usual fix.

4. A rough ranking for a small lot with wire supports.

Doublet or non-resonant dipole on ladder line: the most flexible multiband choice. It needs a tuner and a balun or choke at the shack end, and a total length of at least about 0.3 wavelength on the lowest band. Avoid lengths that put very high impedances on a band you care about. Losses are low, and the pattern is whatever the wire length and height produce.

Inverted V: useful when you have one support. Apex height matters most. An included angle of about 90–120° works, and the resonant length is a few percent shorter than a flat-top dipole. The pattern is more omnidirectional and gain is slightly lower, but that is often a fair trade for one tall support.

EFHW: convenient, with one wire, one feed point and little ground dependence. It is resonant on harmonically related bands (a half-wave on 40m is also a half-wave on 20m, 15m and 10m). Transformer core loss and heating are the main concerns, along with the current-on-shield issue above. Quality of the transformer and choke varies a lot between designs.

OCFD: feeds at about one-third along the wire, typically through a 4:1 balun. It gives a decent match on several bands with one feedline, but the pattern is lopsided on some bands and the match depends on height and surroundings. A choke at the feed is still wise.

G5RV: a 102 ft flat-top with a ladder-line section into coax (a 51 ft half-size version exists). It was designed around 20m and needs a tuner elsewhere. It is not a bad antenna, but it is no better than a plain doublet with an appropriate balun, and the coax transition needs a choke.

Vertical: the best low-angle choice when it works, but it depends on the ground system. A ground-mounted quarter-wave over a few radials loses a lot of power in the soil. Many short radials or several elevated resonant radials make a big difference. A short loaded vertical trades bandwidth and efficiency for size.

Magnetic loop: good for tight spaces and often quieter on receive because it responds mainly to the magnetic field. The bandwidth is narrow, so you retune when you move a few tens of kHz, and efficiency depends on loop diameter, conductor and capacitor quality. Voltages across the capacitor can be very high. It is least efficient on the lowest band you ask it to cover.

5. Height. A horizontal dipole at 30 ft is about 0.44 wavelength up on 20m, which gives a good low-to-medium takeoff angle, but on 80m it is roughly 0.11 wavelength and acts as a high-angle NVIS radiator. Both uses are valid, but they are different goals. If you want DX on 40m and 80m from a small lot, a vertical or an inverted V with a high apex may serve better than a low flat-top.

Questions for the thread. If you can only put up one support, would you take an inverted V doublet on ladder line or an EFHW sloper? Does stealth (thin wire, dark color, trees) change the answer for you? And has anyone compared a compact loaded vertical against a low horizontal wire on the same bands with something more rigorous than A/B signal reports?

  • Replies 2
  • Views 96
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd rank them by how much of the system you can control. The doublet on ladder line wins because the antenna and the feedline are both honest: no transformer to cook, no coax to radiate, and the tuner takes care of the rest. The caveat is that the tuner then dictates your usable range. If the tuner can't handle a few hundred ohms of reactance on, say, 17m, the antenna is not the problem, so check the tuner's actual range before cutting wire. Also keep the ladder line balanced as it leaves the antenna: a few feet of vertical drop, then keep it away from gutters and metal siding. If it runs parallel to a metal surface, the balance degrades and you'll see current on the line anyway.

On the EFHW, I'd split the discussion in two. A well-built transformer, a choke, and a decent counterpoise stub are a nice system. A bare 49:1 box on a long coax run with no choke is a different thing, and it explains most of the 'it works great on the bench, odd in the shack' reports. Power rating also deserves more attention than it gets. Core material, number of turns and the capacitive compensation all change losses on the upper bands, so I'd treat any 'rated 100 W' claim with some suspicion unless the construction is described.

  • Moderators

On the vertical side, the thing I'd add is that 'a vertical needs radials' is true, but the number of radials depends on how they're laid. On or just under the ground, you want many, and the gain from going from 4 to 16 to 32 is real. Raised radials are different: a handful of resonant ones at a few feet up will often outperform dozens of short buried ones for the same effort, and they're easier to hide at the edge of a small yard. If the HOA is the issue, a thin vertical wire on a fiberglass pole can disappear against a tree line, with the radials running along a fence line at ankle height.

On the loop, I'd push back slightly on 'quiet on receive means good.' A small loop's lower noise can make weak signals more readable even when it is 10 dB or more down on a full-size dipole in transmit efficiency. That is fine for monitoring, but for transmit you still care about the efficiency numbers: loop diameter relative to wavelength, conductor diameter, and capacitor losses. A 1 m loop on 40m is a very different animal from the same loop on 15m. The test I'd suggest, if you want a real comparison instead of anecdotes, is to record several known stations, such as WSPR spots or a beacon, on both antennas at the same time and compare SNR over a few days. A single A/B at a single time of day tells you very little.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.