Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

How do you work out where you can legally operate? Band plans vs. FCC rules, band edges, and the VHF/UHF calling frequencies

ci_cover.jpg

This is a question about turning the band charts into real decisions at the radio. Between the FCC rules, the ARRL band plan, license class privileges, and the international differences, it's easy to blur the lines. Here is how I understand it, so please correct anything that's off.

1. Rules vs. band plan. The FCC's Part 97 rules set the legal limits: which frequencies each license class can use, which emission types are allowed in which segments, and the power limits. The ARRL band plan is a voluntary arrangement that divides the space into CW, data, phone, beacon, and simplex areas so different modes don't trample each other. Ignoring it won't get you cited by itself, but you can still cause a lot of interference.

2. HF segments by class. From memory, the pattern is that Extra has the whole allocation, with the bottom edges of 80, 40, 20, and 15 meters being Extra-only CW/data slices. General gets a slightly smaller set of segments on those bands, plus all of 160, 30, 17, 12, and 10 meters (30 meters is CW/data only, with a lower power limit). Technician gets limited CW privileges on 80/40/15, a CW/data and phone slice of 10 meters, and everything on the VHF/UHF bands.

3. 60 meters is channelized in the US rather than a continuous band, and I believe it's USB for voice. I'd like to hear how people verify the current channel list and power limits, since that's an area where rules have changed.

4. Band edges. If I'm on USB near the top of a phone segment, where does the dial need to sit so the sideband stays legal? Same question for LSB near the bottom edge. And how much margin do people leave for radio calibration error?

5. VHF/UHF. I know 146.52 FM is the 2 m national simplex calling frequency, and 446.000 is the 70 cm equivalent. For 6 meters, I'm trying to separate the FM calling channel from the weak-signal sections. What about 33 cm (902–928 MHz)? Is it really that different from 70 cm in practice?

6. International. If the US chart says one thing and ITU Region 1 or 3 says another (40 meters is the example I keep seeing), what governs when I'm talking to DX or operating abroad?

What's your process for checking all this before you transmit?

  • Replies 2
  • Views 41
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Your split between rules and band plan is the right one. The legal question is: does Part 97 allow my license class, this emission, and this power on this frequency? The band plan question is whether I'm using the space the way everyone else expects. Whenever you're unsure, check the current FCC text for the band, since privilege tables on old charts can be out of date.

On band edges, think about where the energy actually is. In USB the carrier is suppressed and the signal sits above the dial frequency by roughly 300 Hz to 2.7 kHz or so, depending on your audio filtering. So at the top of a segment, say a phone limit at 14.350, you want the dial low enough that the whole sideband stays below the limit. In LSB the signal sits below the dial, so near a lower edge such as 3.600 or 3.800 you need to keep the dial a few kHz above it. A reasonable margin is a kilohertz or more beyond the bandwidth, because dial readouts aren't always perfectly accurate and a wide transmit audio setting can spread your signal.

The same applies to digital modes. With FT8 or similar, the signal is at dial frequency plus the audio offset, so a high offset near an edge can push you out. Staying away from edges with the audio tones in the middle of your passband avoids the problem.

Calling frequencies are for making contact and then moving. On 2 m FM, 146.52 is for finding someone, then you QSY to another simplex frequency so the channel stays open. Weak-signal SSB and CW sit in the lower portions of 6 m, 2 m, and 70 cm, away from the FM sections. If you're listening on 6 m for an opening, that's where you'll hear it, not on the FM calling channel.

  • Moderators

A few specifics to add, and as always verify them against the current FCC rules and the current ARRL band plan, because these are the details that change.

60 meters: The US rule has been a set of five specific channels, with USB for voice, and a low ERP limit measured relative to a half-wave dipole. Dial frequencies and channel centers are different numbers, which causes a lot of confusion. The chart you use should say which one it lists. ITU also added a narrow 60 meter allocation at 5351.5–5366.5 kHz, and implementation varies by country. Check what applies to your location before assuming the channel list is the full story.

International: The world is divided into ITU Regions 1, 2, and 3, and the amateur allocations differ. The US is in Region 2. On 40 meters, Region 2 has 7.000–7.300 MHz, while Regions 1 and 3 are narrower at the top. So a US station might legally transmit on a frequency where a European station can't answer, and that's the other station's problem to manage. If you operate from another country, the rules of the country you're in apply, along with whatever reciprocal arrangement covers your license. Look that up before you travel; don't assume your home privileges carry over.

33 cm: It's not like 70 cm in a few ways. The 902–928 MHz band is Region 2 only, so there's no worldwide allocation to rely on. Amateurs share it with other services, including unlicensed Part 15 devices, and noise and interference from those can be significant. Activity is also much thinner, mostly weak-signal and some repeaters and experimenters, so the plan matters if you want to find anyone. 70 cm has some geographic restrictions too, particularly near borders and where certain government radar operations exist, so read the notes on that band.

For a practical check, I'd keep the FCC privilege chart for your class, the ARRL band plan, and the digital mode frequency list you use all in one place, and look at the date on each one.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.