Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a first homebrew QRP station: what to build first, and which test gear is worth having

ci_cover.jpg

I'm sketching a build order for a small CW/SSB QRP station and would like opinions on the sequence. The tempting plan is to jump straight to a transceiver (a BITX-style board, a uBITX, or a Pixie-class toy) and sort out the accessories later. But a transmitter without a known load, a filter and a way to measure power is mostly a way to make unknown RF.

This is the order I'm leaning toward:

1. Power supply and bench basics. A fused 12-13.8 V supply with a reverse-polarity diode, a current-limited bench source if possible, and ferrite or LC decoupling on the radio's supply input. Cheap switching supplies can put noise all over HF, which a sensitive direct conversion receiver will show you immediately.

2. Dummy load and RF probe. Several 2 W metal-film or carbon-film resistors in parallel make a perfectly good QRP load. Four 200 ohm resistors in parallel give 50 ohms at 1 W each for a 4 W total rating, with a fair margin at 1-5 W if you keep the keying duty cycle reasonable. A diode RF probe for the DMM gives a rough voltage reading. Peak voltage across 50 ohms converts to power with P = Vpeak² / (2 × 50), after correcting for diode drop.

3. Low-pass filter for the band I'll use. A 5-element Chebyshev or Butterworth low-pass built on powdered-iron toroids (T37-2 or T50-2 are common for QRP) is the usual choice. The value of this stage is that you can check it with a NanoVNA before it ever sees a transmitter.

4. SWR bridge. Either a tandem-match style directional coupler or a resistive return-loss bridge. The bridge is good for tuning antennas at low power, while the coupler can stay in line during operation.

5. Receiver, then transmitter, then keyer. A direct conversion receiver teaches a lot cheaply, and a keyer is a small digital project that can come last.

Where would you reorder this? And what would you buy first as test equipment: a NanoVNA, a used oscilloscope, a frequency counter, or something else?

  • Replies 2
  • Views 36
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd keep your order but move the low-pass filter earlier, ahead of any transmitter you build, since a lot of simple transmitters, including Tuna Tin 2-style crystal oscillators and Pixie-like designs, are not clean outputs. A single-transistor stage running into a resonant output network can still carry substantial harmonic energy. The filter fixes a lot, but you still have to verify the result.

For test gear, a NanoVNA-type instrument is probably the best value for filters, antennas and return loss. It's less useful for looking at your transmitter's output spectrum unless you add a suitable attenuator and know what you're doing, because plugging a transmitter into a VNA port can damage it. Use a dummy load and a proper attenuator chain, or use a different method altogether.

For checking harmonics without a spectrum analyzer, a common trick is to listen on a separate receiver tuned to the second and third harmonic frequencies, with the transmitter into a dummy load and a short sample of the signal. It's crude, but it tells you whether there's a problem. A scope is more general-purpose than a counter. A counter is nice for setting up a VFO or crystal oscillator, but a scope will also show you audio, keying waveforms, supply ripple and DC problems.

  • Administrators

On the receiver, a direct conversion design is a good teaching build, but expect some quirks. A basic product detector like an NE602/SA612-type mixer or a diode-ring mixer, followed by a high-gain audio chain, will hear both sidebands at once. There's no image rejection unless you add a phasing network, so a CW signal appears on both sides of zero beat. That isn't a defect, it's how the architecture works.

The usual trouble spots are AM broadcast breakthrough, hum from the supply, and microphonics from loose components or long wires. A band-pass filter at the front end helps with the first, good decoupling helps with the second, and mechanical stiffness handles the third. A simple audio low-pass or peaking filter after the mixer makes CW listening much more comfortable.

For the transceiver step, a BITX-type design is attractive because it reuses the same bidirectional amplifier stages in both receive and transmit. The uBITX adds a microcontroller and a Si5351 synthesizer for multiband coverage. Anything with a digital synthesizer deserves a careful look at spurious outputs and filtering. Whatever you choose, read the builder's notes for that board and measure the output on your own unit before putting it on the air.

One soldering tip for the toroid filters: enamel wire must be fully stripped (by scraping or with a hot, well-tinned iron) before it'll make a real joint. A bad connection there can look fine and still detune the filter. Count turns through the core's center hole, and check the finished filter's response on the VNA before installing it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.