Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Choosing a VHF/UHF antenna: J-pole vs 5/8 collinear vs yagi, and where installation matters more than the antenna

ci_cover.jpg

I'd like to compare notes on the usual VHF/UHF antenna choices and on the installation details that decide how they perform. The 2 m and 70 cm bands are forgiving enough that almost anything will make some noise, so differences between setups often come from feedline, grounding and placement rather than the antenna's name.

Starting with the common vertical designs. A quarter-wave whip is about 19 in (roughly 49 cm) long on 2 m and about 6.3 in on 70 cm. It is simple, broadband and rugged, and it relies on a ground plane, which on a vehicle is the roof. A 5/8-wave whip is longer and has a lower radiation angle, so it usually gives a couple of dB more at the horizon when the ground plane is decent. It needs a matching coil or network at the base to present a sensible impedance, and it depends on that ground plane to work as designed.

The J-pole is an end-fed half-wave with a quarter-wave matching stub. The slim jim is a close relative: a folded J-pole with an open stub and a long, thin shape. Both are popular for home-built base antennas and both are vertically polarized and omnidirectional. They are often described as not needing radials, but the feedline can act as part of the antenna, because common-mode current flows on the coax shield. A choke of several turns of coax, or ferrite on the feedline near the feedpoint, can help keep the pattern predictable and reduce RF in the shack.

On gain: dBd is relative to a half-wave dipole and dBi is relative to an isotropic radiator, a difference of 2.15 dB. Be skeptical of an advertised number without the reference. On an omni vertical, extra gain comes from squashing the pattern toward the horizon, not from creating power. That is great for flat terrain and for reaching a distant repeater, but if you are in a valley or on a steep hillside a high-gain collinear can put the main lobe over the people you are trying to talk to.

For directional work, a yagi gives much more usable gain, with typical amateur designs in the 6 to 12 dBd range depending on boom length, plus front-to-back rejection that also helps cut interference from the sides and rear. Orientation matters. Mount it vertically for FM repeater work and horizontally for weak-signal SSB/CW. Cross-polarization loss can be large, and in practice 10 to 20 dB is not unusual.

On the feedline side, loss rises quickly with frequency. Rough figures: RG-58 is about 10 dB per 100 ft at 450 MHz, while LMR-400-class cable is about 2.7 dB per 100 ft. On 2 m the numbers are lower but still matter on a long run. If you have a 50 ft run to a 70 cm antenna, the coax choice can outweigh any 3 dB antenna upgrade.

Connectors: PL-259/SO-239 are common and acceptable on 2 m, but they are not constant-impedance and are not waterproof. On 70 cm and up, or on any outdoor connection, N-type is the better choice, since it has a gasket and a defined impedance. Whatever you use, seal outdoor connections with self-amalgamating tape and then a layer of vinyl tape, and form a drip loop so water does not follow the cable into the connector.

One more thing on SWR. A low reading says the transmitter sees a good match. It does not say the antenna is radiating well, because a dummy load also shows 1:1. A lossy coax run also improves the SWR you read at the radio end, since reflected power is attenuated twice on its way. If possible, check with an antenna analyzer at the antenna feedpoint.

For mobile installs, NMO mounts are a solid choice: a 3/4 in hole and a mount with good metal-to-metal contact to the body. A magnetic mount is easy to remove, but it depends on capacitive coupling to the roof, can scratch paint if dirt gets under it, and the cable running through a door seal can get pinched. Placing the mount at the roof center gives the most uniform pattern.

For satellites, FM LEO passes on 2 m/70 cm are possible with a handheld and a small handheld yagi, such as an Arrow-type, and some people use a crossed yagi with circular polarization to reduce fading. With linear antennas, polarization changes as the satellite rotates, so expect fading, and you may need to rotate the antenna to keep the signal up.

Questions for the thread: what are you running now, and what is its biggest limitation: coverage, noise, TX range, or mounting? If you were choosing between a collinear and a small yagi for repeater access, how would you decide? And do you use a choke on J-pole/slim jim feedlines?

  • Replies 2
  • Views 43
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the collinear-versus-yagi question, I'd start with terrain and the number of repeaters you need. If everything you want is in roughly one direction, a small vertical yagi gets you more gain and less pickup from the other directions. If the repeaters you use are scattered around the compass, a rotator adds cost and complexity, and a decent omni at height is usually the easier answer.

Height beats gain at VHF/UHF line-of-sight distances. A 3 dBd antenna at the top of a mast can outperform an 8 dBd antenna that is stuck low and surrounded by obstacles. Keep the radiating element clear of the mast too: for a vertical omni on a metal mast, use a side mount or an offset arm that places the antenna a good distance from the mast, because the mast can distort the pattern. Some designs are intended to be mounted on top of the mast, so check the instructions.

For a slim jim, a common mistake is to cut the length once and never verify it. Dimensions that look fine on paper change with the wire, spacing, the feedline connection and anything nearby. An analyzer is the right tool to find the resonant point and trim from there, and I'd check the SWR with the antenna in its final position.

  • Moderators

Adding a few details on the mobile and connector side. The 5/8 wave on a vehicle works best if the ground plane is a reasonable size. On a small roof or on a trunk lid mount, the pattern can tilt and the SWR can be less friendly than on a roof center install. With a quarter-wave, the sensitivity to mount location is smaller, so it's a good choice if you can't mount in the center.

If you're making your own cable for an NMO mount, make sure the shield makes proper contact at the mount and that the center conductor isn't shorted when you solder or crimp. Many mounts come with the coax already attached; if you're replacing it, use a mount style that matches your coax size. I'd skip adapters wherever possible. Each extra connector adds a point of loss and a place for water to get in, so a PL-259 to N adapter on the roof is a weaker choice than a single N-type connection built into the cable.

For satellite use, the easiest improvement to a handheld setup is a beam with a gain you can point. Keep the handheld's rubber duck for portable use, but when you point a yagi at a pass, you'll need to track the satellite and account for Doppler shift. For FM satellites, that means adjusting the receive and transmit frequencies in steps through the pass. The antenna choice makes less difference if you can't hear the satellite, so work out the pass times and elevation before spending money.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.