ⓘ Callsign lookups are in real time via the FCC database.
Vanity callsign availability is refreshed daily at 6:00 AM CST.
The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cmvia PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHzDXSpotterInfo
Recent spots—
Select a band above to load spots
Ready — select a band to fetch live spots
SSB audio that carries: mic gain, ALC, compression and bandwidth for weak stations and DX
Most SSB audio problems come from the same few settings: mic gain too high, too much processing, and a transmit EQ that favors what sounds good in the headphones over what carries through noise. Here is a baseline to argue with or improve on.
Sideband choice. The convention is LSB below 10 MHz (160, 80 and 40 m) and USB above it (20, 17, 15, 12 and 10 m). On 60 m, USB is the norm because of the channelized allocation. The reason is historical, not technical, but the convention means everyone's passband lands where the other station expects it. Tuning in the wrong sideband just makes the audio sound like garbled duck noise, so if a station sounds unintelligible, check this first.
Mic gain and ALC. ALC is a safety net, not a loudness control. Set mic gain so that your normal speaking voice moves the ALC meter only on peaks, and stays inside the rig's recommended zone. If the ALC is pinned on every syllable, the transmitter is flattening your peaks, which creates distortion and splatter, and the cleanup does not make you more readable. Meter behavior varies by radio, so check the manual for what the ALC zone means on your model. If you run an amplifier, keep the exciter clean and make sure you are not driving the amp into its own ALC or flat-topping the output.
Speech processing and compression. Compression raises the average-to-peak ratio, which helps when the other station is copying you near the noise floor. A few dB of compression (often something like 3 to 6 dB on the rig's compression meter, if it has one) usually helps. Push it harder and you get a raised background, breath noise, room noise, sibilance and a pumping effect. RF clippers and heavy processing also widen the signal's occupied bandwidth through intermodulation products, which hurts the people operating next to you. Use the minimum that gets you through, and turn it off when conditions are good and the band is quiet.
EQ and bandwidth. Low frequencies carry a lot of power but little intelligibility. Rolling off below about 200 to 300 Hz often cleans up the sound and frees headroom for the speech peaks. A gentle lift in the 2 to 3 kHz region helps consonants cut through noise. Most rigs transmit around 2.4 to 2.7 kHz by default, and on a crowded band there is little reason to go wider. A wider transmit passband can sound nicer on a quiet band for a casual chat, but it takes up more room and spends power on content that does not help in a pileup.
Monitoring. Use the monitor function with headphones so you avoid feedback, and watch the level: monitor audio is generally what your rig processes before the final RF stage, so it will not show you splatter or poor linearity. For a true check, ask a nearby station for a report, record yourself on a remote SDR if you can, or use a second receiver on a dummy load or a low-power path to inspect your signal width.
Receive side. A 2.4 kHz filter is a good general starting point. For weak stations in QRM, narrowing to around 1.8 to 2.1 kHz, or using passband shift or IF shift to move the filter away from an adjacent signal, often improves copy more than noise reduction does. Treat NR carefully, because heavy settings smear speech and can hide the very details you need for a callsign. On the lower bands, check whether the preamp is helping or just raising the noise. AGC speed matters too: a slow AGC can hold down a weak signal after a strong burst of noise.
Working DX. Mic technique counts: keep a consistent distance from the mic, speak slightly off-axis if plosives are a problem, use a pop filter, and avoid a room with echoey walls. Listen for the DX station's pattern, including whether they are operating split, and give your callsign clearly using standard phonetics. Don't shout. Over-driving the mic gives you distortion, not range.
What are your go-to settings for compression, EQ and filters? And when you adjust for a pileup, do you change the audio first or the receive filter first?
Most SSB audio problems come from the same few settings: mic gain too high, too much processing, and a transmit EQ that favors what sounds good in the headphones over what carries through noise. Here is a baseline to argue with or improve on.
Sideband choice. The convention is LSB below 10 MHz (160, 80 and 40 m) and USB above it (20, 17, 15, 12 and 10 m). On 60 m, USB is the norm because of the channelized allocation. The reason is historical, not technical, but the convention means everyone's passband lands where the other station expects it. Tuning in the wrong sideband just makes the audio sound like garbled duck noise, so if a station sounds unintelligible, check this first.
Mic gain and ALC. ALC is a safety net, not a loudness control. Set mic gain so that your normal speaking voice moves the ALC meter only on peaks, and stays inside the rig's recommended zone. If the ALC is pinned on every syllable, the transmitter is flattening your peaks, which creates distortion and splatter, and the cleanup does not make you more readable. Meter behavior varies by radio, so check the manual for what the ALC zone means on your model. If you run an amplifier, keep the exciter clean and make sure you are not driving the amp into its own ALC or flat-topping the output.
Speech processing and compression. Compression raises the average-to-peak ratio, which helps when the other station is copying you near the noise floor. A few dB of compression (often something like 3 to 6 dB on the rig's compression meter, if it has one) usually helps. Push it harder and you get a raised background, breath noise, room noise, sibilance and a pumping effect. RF clippers and heavy processing also widen the signal's occupied bandwidth through intermodulation products, which hurts the people operating next to you. Use the minimum that gets you through, and turn it off when conditions are good and the band is quiet.
EQ and bandwidth. Low frequencies carry a lot of power but little intelligibility. Rolling off below about 200 to 300 Hz often cleans up the sound and frees headroom for the speech peaks. A gentle lift in the 2 to 3 kHz region helps consonants cut through noise. Most rigs transmit around 2.4 to 2.7 kHz by default, and on a crowded band there is little reason to go wider. A wider transmit passband can sound nicer on a quiet band for a casual chat, but it takes up more room and spends power on content that does not help in a pileup.
Monitoring. Use the monitor function with headphones so you avoid feedback, and watch the level: monitor audio is generally what your rig processes before the final RF stage, so it will not show you splatter or poor linearity. For a true check, ask a nearby station for a report, record yourself on a remote SDR if you can, or use a second receiver on a dummy load or a low-power path to inspect your signal width.
Receive side. A 2.4 kHz filter is a good general starting point. For weak stations in QRM, narrowing to around 1.8 to 2.1 kHz, or using passband shift or IF shift to move the filter away from an adjacent signal, often improves copy more than noise reduction does. Treat NR carefully, because heavy settings smear speech and can hide the very details you need for a callsign. On the lower bands, check whether the preamp is helping or just raising the noise. AGC speed matters too: a slow AGC can hold down a weak signal after a strong burst of noise.
Working DX. Mic technique counts: keep a consistent distance from the mic, speak slightly off-axis if plosives are a problem, use a pop filter, and avoid a room with echoey walls. Listen for the DX station's pattern, including whether they are operating split, and give your callsign clearly using standard phonetics. Don't shout. Over-driving the mic gives you distortion, not range.
What are your go-to settings for compression, EQ and filters? And when you adjust for a pileup, do you change the audio first or the receive filter first?
Link to comment
https://www.hamradiobase.com/forums/topic/11048-ssb-audio-that-carries-mic-gain-alc-compression-and-bandwidth-for-weak-stations-and-dx/Share on other sites