Repeater basics to linked systems: offsets, tones, time-outs and how not to annoy the machine's owners
- Replies 2
- Views 44
- Created
- Last Reply
A better way to browse. Learn more.
A full-screen app on your home screen with push notifications, badges and more.
This thread is meant as a common reference for people moving from simplex into repeaters, and for people who already use repeaters but get confused once linking is involved. Add corrections and regional differences, because the details vary a lot by country and even by region.
Offset and tones are separate settings. A repeater receives on one frequency (its input) and transmits on another (its output). The difference is the offset. In the US, 2 m repeaters usually use 600 kHz, with the sign depending on the sub-band, and 70 cm usually uses 5 MHz. Other countries use different standards. In much of Europe, for example, 70 cm commonly uses 7.6 MHz. Your radio's automatic repeater offset is only a guess based on a band plan, so check it against the actual listing. The offset only gets your radio on the right frequencies. Many repeaters also require an access tone before they will repeat you.
CTCSS (often called PL, which is a Motorola trademark) is a continuous sub-audible tone, roughly 67 to 254 Hz, transmitted along with your voice. Most repeaters need it on their input. Some repeaters also send a tone on their output, and some do not. These are different settings. "Tone" on most radios means you encode a tone when transmitting. "Tone squelch" (TSQL) means your receiver stays muted until it hears the matching tone. Tone squelch is useful if you want to cut out other users on a busy channel, but it can mislead you if you forget it is on. A "dead" repeater may simply be sending no tone, or a different one than you set. Many radios also have a reverse-tone function that opens the squelch when the tone is absent, which is handy for checking whether you can hear the repeater input directly.
DCS (digital coded squelch) does the same job with a continuous low-speed digital code instead of an analog tone. Codes are written as three-digit octal numbers, usually with an N or I suffix for normal or inverted polarity. If a DCS code seems right but nothing works, the polarity is a common culprit. Be careful with terminology: D-STAR also has "DCS" reflectors, which are an unrelated networking system that happens to share the abbreviation.
Time-out timers and courtesy tones. Most repeaters have a time-out timer (TOT) that drops the transmitter if one user keys up for too long. Three minutes is a common value, but there is no universal setting, and you should not rely on it as a normal operating limit. Many repeaters also have a courtesy tone that signals the machine is ready for the next transmission. Wait for it, since it can help stop the repeater from timing out. A hang time, the brief interval after you unkey before the transmitter drops, affects the courtesy tone and your pacing. On a linked repeater, the delay may be longer, because the linked system has to unkey and be ready for the next user.
Open, closed and limited. An open repeater is available to any licensed amateur within the rules. A closed repeater restricts access to members or approved users, often by a tone that is not published. Some systems are "limited" and have restrictions such as a membership requirement or reserved times. Directories often list this, but they are only as current as the information the owner submitted. If a listing says "open" and your tone is correct but you cannot access it, check with the club or the trustee before assuming the machine is broken.
Coordination. In many places, a frequency coordinator (usually a regional volunteer organization) recommends repeater frequency pairs and tones to reduce mutual interference. In the US, coordination is voluntary but carries weight, because FCC rules place more responsibility on an uncoordinated repeater to resolve interference with a coordinated one. Rules and bodies differ elsewhere, so consult your national society or regional coordinator before putting up a machine.
Linked systems. Linking gives a local repeater access to a wider audience. The main systems are:
EchoLink is a VoIP system that connects stations and repeaters over the internet and verifies licenses. It works from a computer, a phone or a node connected to a repeater. IRLP uses node numbers and reflectors and is controlled by DTMF. AllStarLink is based on Asterisk and uses node numbers and DTMF commands, and it can link repeaters and simplex nodes into larger networks. Wires-X is Yaesu's System Fusion network and uses nodes and rooms. DMR (time-division multiple access) uses time slots, color codes and talkgroups, and the radio needs a codeplug with the right contacts, plus a registered DMR ID. D-STAR uses callsign routing and reflectors, with the repeater fields (RPT1, RPT2 and URCALL) controlling where traffic goes.
The important thing in every linked system is to find out what is connected before you transmit. On a linked machine you may be talking to a lot of listeners at once, including people who have no way to answer you through the local repeater.
Etiquette summary. Listen before you transmit, since the channel may be in use or part of a net. Give your callsign when required, and as often as your regulations require. Keep transmissions short and leave a gap so someone can break in, especially in emergencies. Do not kerchunk (keying up without identifying) to test the repeater. Say your callsign and ask for a signal report instead. Do not conduct business or play music through the machine. Respect the owner's rules about nets, topics, autopatch and linking. Finally, check the ownership and policy of the repeater, because an open repeater is still privately funded and maintained.
What are the common settings mistakes you see when someone says "the repeater doesn't work"? And what do clubs do to explain linking etiquette to newcomers?
Link to comment
https://www.hamradiobase.com/forums/topic/11073-repeater-basics-to-linked-systems-offsets-tones-time-outs-and-how-not-to-annoy-the-machines-owners/Share on other sites