Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dead or misbehaving rig: a practical troubleshooting order from power supply to finals to alignment

ci_cover.jpg

Most repair threads start with "it's dead" or "it receives but won't transmit" and then jump straight to blown finals. Finals do fail, but they are not the most common culprit, and replacing them without finding the cause often just destroys the new ones. This is a working order of attack that applies to most solid-state HF and VHF/UHF transceivers. Please add or correct anything.

1. Start with power, and measure it under load. A supply that reads 13.8 V with no load can sag badly when the rig draws current. Check the voltage at the rig's DC connector while receiving and while transmitting. Check the fuses in the power cable and inside the radio. A fuse can look fine and still have a corroded holder, and a high-resistance connection in the cable or plug can drop volts exactly when transmit current flows. If the rig is internally regulated, check the main rails (typically 5 V, 8 V or 9 V, and so on, depending on the model) against the service manual before you touch anything else. With a switch-mode supply, remember that it can cause both noise and odd behaviour even when the DC reading looks right.

2. Split the problem: receive, transmit, or both. "No receive and no transmit" usually points to something common to both paths: power, the PLL or reference oscillator, the antenna relay or switching, or the CPU and control logic. If the display and keys respond but there is no receive, check the audio path (speaker jack, AF gain, squelch setting, DSP or audio amp), then RF gain, attenuator and preamp settings, then antenna relay contacts. A rig that receives only weakly on one band can point to a band-switching diode, a dirty relay, or a faulty band-pass filter path.

3. No transmit: check the signal chain before the finals. Always use a dummy load. Confirm that the PTT line actually switches the radio to transmit (listen for the relay, look for the TX indicator), and that the mic or data input has audio. Then look for drive from the exciter to the driver, bias voltages on the driver and final stage, and whether ALC or protection is pulling the drive down. Many rigs show no output simply because a protection circuit is holding the drive down, not because a transistor has failed.

4. SWR protection faults. If a rig folds back power or shows a high-SWR indication into a good dummy load, suspect the reflected-power detector rather than the antenna. Look at the directional coupler or bridge, its detector diodes and filter capacitors, and the calibration trimmers. If the fault only shows on one band, check the low-pass filter relays and filter components for that band. If it only appears on the antenna, suspect the coax connectors, a water-damaged feedline, or the antenna itself. The dummy load test splits those two cases quickly.

5. Noise. Work out whether the noise comes from outside the radio (switch-mode supplies, LED lighting, other devices) or inside it. Run the rig from a clean linear supply or a battery and disconnect the antenna. If the noise stays, it is internal. Internal causes include failing electrolytic capacitors that no longer filter the supply, dirty or worn pots and switches (crackling when you turn them), and poor ground connections in the chassis. A scope on the supply rails will show ripple that a multimeter would not reveal.

6. Blown finals: find out why they died. Typical root causes are high SWR with weak protection, bias circuit faults that allow thermal runaway, parasitic oscillation, an overvoltage event, or a driver stage problem. Before fitting new devices, check bias resistors and diodes or thermistors in the bias network, protection devices, the output filter and relay, and anything else around the failed transistors. Use the correct replacement type, or a properly matched pair where the design needs one. Set bias according to the service manual, with current monitored on a current-limited bench supply.

7. Capacitor replacement. Electrolytics age, and in older equipment they are a sensible suspect for supply and audio problems. Some surface-mount electrolytics also leak, and the electrolyte can eat the traces beneath them. Replace like with like in capacitance and voltage rating, observe polarity, and clean any residue thoroughly. Do not replace every capacitor on spec. Measure first (ESR meter, ripple on the scope) and change the ones that are actually suspect or known to fail on that model.

8. Cleaning contacts. Isopropyl alcohol and a dedicated electronic contact cleaner solve many intermittent problems in switches, pots, relays and connectors. Use small amounts, work the control back and forth, and let it dry. Be careful with plastics, and do not lubricate where a lubricant is not called for. Also check coax connectors, power plugs and internal board-to-board connectors, which are a very common source of intermittent faults.

9. Alignment comes last. Alignment cannot cure a hardware fault. Once the rig is working, follow the service manual's alignment procedure: it will list the equipment needed (signal generator, frequency counter, dummy load, power meter, a DMM or RF voltmeter) and the correct order of adjustments. Do not turn trimmers or coil slugs without noting their original positions and without a reference procedure.

10. Service manuals and test equipment. The manual's block diagram, voltage tables and test points save hours. A basic bench kit that covers most jobs is a DMM, a current-limited variable supply, a dummy load with a wattmeter, a scope with a proper probe, an RF probe or a signal generator, and a way to measure frequency. A NanoVNA is useful for filters, antennas and coax checks. Remember that mains, large reservoir capacitors, and any tube stage with high voltage can all be dangerous. Discharge and verify before working.

What order do you follow when a rig comes in with an unspecific fault, and which quick checks do you think are worth doing first?

  • Replies 2
  • Views 49
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I would put one thing above everything else in that list: use a current-limited bench supply for the first power-up after any repair, and watch the ammeter, not just the display. A rig that normally idles at a modest current and suddenly pulls far more is telling you a lot before you've touched a probe. If current is high on receive only, look at a shorted bypass capacitor or a failed regulator. If it jumps only on transmit, it points toward the PA, the bias circuit, or the driver.

On the scope, a few cautions. Use a proper 10x probe and a short ground spring when you look at supply ripple, because a long ground lead picks up its own noise and can mislead you. Keep the scope on AC coupling and a small volts-per-division setting for ripple, and remember that a 'clean' DMM reading tells you nothing about it. If the noise changes when you touch a particular board or cable, work toward that area, then check grounds and shield connections.

One small extra for the SWR section: if the protection trips even into a known-good dummy load, compare the forward and reflected detector voltages at the sense board with the manual's values. A leaky detector diode or a failed filter capacitor can look exactly like a mismatch.

  • Moderators

On blown finals, the point about the cause is worth stressing. If a pair of transistors has died, I would treat the bias circuit as guilty until it has been measured. A damaged bias transistor, a bad thermal-sense device, or an open preset can send bias the wrong way. Before applying power with new devices, check the bias voltage with the finals disconnected or with the supply current limited, set the bias control to the minimum position the manual specifies, then bring it up gradually while watching idle current. Do not rely on a 'good enough' guess.

It is also worth testing the output stage for stability. Parasitic oscillation can destroy devices even when SWR is fine, and it may show up as odd current draw with no RF drive or as spurious signals on a spectrum analyser or a second receiver. Check that the emitter or source resistors, feedback networks, ferrite beads and any snubber parts are intact and correct. Those small parts are easy to overlook next to the transistors.

For alignment, I would add: take readings before you change anything and write them down. Many rigs have a few alignment steps that interact, and if you don't know where you started, you can't get back. If the manual calls for a particular test signal level or a particular dummy load, use that instead of whatever is nearest. It costs little and makes the result repeatable.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.