Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Choosing a VHF/UHF antenna: J-pole vs slim jim vs collinear vs yagi, and what SWR doesn't tell you

ci_cover.jpg

There are a lot of 2 m / 70 cm antenna choices, and the marketing numbers rarely help. Let's try to sort out what actually changes your results: pattern, polarization, feedline loss and installation. Gain figures come last.

Omni vertical options. A J-pole is an end-fed half-wave with a quarter-wave matching stub. A slim jim is a close relative with the stub folded into a slim, tall shape. Both are cheap and usually give roughly unity gain or a bit better, with a fairly low takeoff angle. Because they're end-fed, they don't depend on a ground plane the way a quarter-wave whip does. That also means the coax shield can become part of the antenna. Without a choke (a few turns of coax or a ferrite choke near the feedpoint) and some distance from a metal mast, common-mode current can distort the pattern and shift the apparent SWR.

Collinears. Stacking phased half-wave or 5/8-wave sections squeezes the pattern in the vertical plane, so more energy goes toward the horizon. That helps on flat terrain. It can hurt if you're in a valley or below a repeater on a hill, where you may need some upward radiation. Be skeptical of dBd versus dBi on the packaging. A 3 dB difference on paper is just the 2.15 dB reference difference plus whatever optimism the maker added.

Yagis. A yagi trades coverage for gain. As a rough rule, doubling boom length in a well-designed yagi adds about 3 dB. Beamwidth narrows, so rotating or aiming becomes part of the job. For FM repeater work, mount it vertically polarized to match everyone else. For SSB/CW weak-signal work on 2 m and 70 cm, horizontal is the usual convention.

Polarization. Cross-polarized paths can lose a lot of signal, in theory 20 dB or more. Real paths with reflections are usually less severe but still noticeable. A tilted handheld antenna and a vertical repeater antenna also don't match perfectly.

Feedline and connectors. Coax loss rises quickly with frequency. Typical figures are around 4–5 dB per 100 ft for RG-58 on 2 m and noticeably worse on 70 cm. Low-loss 400-class cable is around 1.5 dB per 100 ft at 2 m and under 3 dB at 70 cm. Check the datasheet for your cable, because numbers vary by manufacturer. PL-259 (UHF) connectors are fine for HF and acceptable on 2 m, but they aren't constant-impedance. For 70 cm and anything outdoors, N-type is a better choice, and its gasket helps keep water out.

SWR. A 1.5:1 SWR reflects about 4% of the power at the mismatch, and 2:1 reflects about 11%. Those numbers aren't the real issue. SWR measured at the radio through a long run of lossy coax will look better than it is at the antenna, because the loss attenuates the reflected wave. A low reading also doesn't prove the antenna radiates well, since a dummy load has a perfect SWR.

So what are you trying to cover: a local repeater, simplex across town, or satellite passes? And what mounting constraints (roof, mast, vehicle) do you have? Those usually decide the antenna more than the gain rating does.

  • Replies 2
  • Views 35
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

For mobile use, the ground plane matters more than most people expect. A quarter-wave whip is about 19–20 in at 2 m (about 6.5 in on 70 cm) and works against the vehicle body. An NMO mount in the center of the roof gives the most symmetrical pattern, and it's electrically and mechanically solid because the base is bolted to the roof skin through a hole (3/4 in is the standard size). A mag mount is quicker and needs no drilling. But it couples to the body capacitively, so the metal under it needs to be clean and flat, and the cable gets pinched where it passes the door seal. Scratched paint and a poorly seated magnet can cause an intermittent SWR.

A 5/8-wave whip is longer than a quarter-wave and has a base loading coil for matching. It's often rated at about 3 dBd, with a lower takeoff angle than a quarter-wave. That figure assumes a decent ground plane. On a small or fiberglass roof, the extra gain on paper may not appear, and the antenna may also be harder to tune. On a vehicle with a good metal roof, either is a legitimate choice. A quarter-wave is more forgiving, and a 5/8 wave typically does better on weak, flat-terrain signals.

A practical tip: tune or check SWR across the whole band of interest, not at one frequency, and do it with the doors closed and the antenna in its final position.

  • Moderators

On satellites, antenna choice is mostly about polarization and pointing. Many amateur satellite downlinks and uplinks are linearly polarized at the spacecraft. Since the satellite's orientation changes through a pass, a fixed linear antenna on the ground will see deep fades. A circularly polarized antenna (typically crossed yagis fed with the proper phasing) reduces that. Using a handheld three-element dual-band yagi and manually tilting it sometimes works for strong passes, though you pay for it in polarization mismatch and pointing errors. Doppler shift matters too, so the radio side needs to allow retuning during the pass.

For repeaters, the antenna is only part of the story. A repeater needs enough isolation between its transmit and receive antennas or duplexer. In a duplexed system, a collinear omni on a tall mast and low-loss, well-weatherproofed N-type connections are the common approach. Water in a feedline connection can degrade a repeater long before anyone notices. For repeater access from home, a vertical yagi pointed at the machine often beats an omni, because it improves both receive and transmit and rejects off-axis interference.

One more point on SWR: if you can, check it at the antenna end of the feedline with an analyzer. If it looks very different from the reading at the radio, the coax loss or a connector is hiding a problem.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.