Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Choosing between J-pole, slim jim, collinear and 5/8 mobile antennas: what matters more, gain or feedline and installation?

ci_cover.jpg

Antenna choices on 2 m and 70 cm often start with gain figures on a box. In practice the result depends on a few things working together: the antenna type, how well it is isolated from the feedline, the ground plane (if it needs one), the coax loss, and the height and clearance of the install. This thread is for comparing common designs and sorting out which claims hold up.

Quarter-wave whip vs 5/8 wave. A quarter-wave whip is about 19 in (48 cm) on 2 m and about 6.5 in (16.5 cm) on 70 cm. It is simple, rugged and presents a feed impedance close to 50 ohms over a decent ground plane. A 5/8 wave is taller, roughly 50 in on 2 m, and uses a matching coil at the base. It has more gain in theory (around 3 dB over a quarter-wave), with a lower radiation angle. That advantage depends on a good ground plane. A 5/8 on a small or off-center ground can lose most of its benefit and may show an erratic pattern. On a vehicle, a roof-center NMO mount usually behaves best, a trunk-lip mount less so, and a mag mount is somewhere in between depending on contact with the body and the size of the metal around it.

NMO vs mag mount. NMO needs a roughly 3/4 in hole but gives a solid, repeatable connection and a ground that does not depend on capacitive coupling. A mag mount is quick and removable, but it is easy to get a poor ground (paint, dirt, a mount sitting on a rough surface), and the thin coax commonly supplied is lossy at 70 cm. Both need coax routed so it is not pinched in a door seal.

J-pole and slim jim. Both are end-fed half-wave radiators with a quarter-wave matching section. They do not need a ground plane, which is why they are popular as base antennas. Their gain is close to a half-wave dipole, so be skeptical of figures like 6 dB. The weak point is common-mode current: without a choke or decoupling, the coax outer can become part of the radiator. That distorts the pattern and can change the SWR depending on how the cable is moved. A slim jim is a folded variant in a long, thin form. A well-built one often has a good low-angle pattern, but the gain is not dramatically higher than a J-pole.

Collinears and yagis. A collinear stacks phased elements to squeeze the elevation pattern and add gain in all horizontal directions. Higher gain means a narrower vertical beamwidth, which can be a disadvantage in hilly terrain or when the antenna is mounted very high near the target stations. Mounting matters too: a vertical collinear attached directly to a metal mast can distort the pattern, so use an offset arm or follow the manufacturer's spacing. A yagi gives directional gain, typically in the 6 to 12 dBi range depending on boom length. It is used for repeaters at the edge of coverage, weak-signal work and satellite work. Polarization matters here. FM voice on 2 m and 70 cm is conventionally vertical, while SSB/CW weak-signal work is conventionally horizontal. Cross-polarized stations can lose a lot of signal.

Coax, connectors and SWR. Coax loss rises quickly at 70 cm. Approximate figures: RG-58 is around 10 dB/100 ft at 450 MHz, while LMR-400-type cable is under 3 dB/100 ft. Check the datasheet for the exact cable. For outdoor runs, N-type connectors are a better choice than PL-259/SO-239 (the 'UHF' connector). N-type is constant-impedance, has a gasket, and holds up better at UHF. PL-259s are fine for many short VHF runs, but they are not impedance-controlled and are easy to water-soak. Weatherproof any outdoor connection properly with self-amalgamating tape and a protective outer wrap.

One common SWR trap: measuring at the radio end of a lossy cable makes the antenna look better than it is, because the reflected power is also attenuated by the cable. A low SWR does not prove the antenna is radiating efficiently. A dummy-load-like result can look excellent on the meter. Measuring at the antenna end with an analyzer, or at least knowing the cable loss, gives a better picture.

Repeater and satellite antennas. A repeater site typically uses a vertically polarized omnidirectional collinear, or a directional antenna when coverage needs to be shaped. It also needs good isolation between transmit and receive (duplexer or sufficient separation), low-loss feedline and grounding/surge protection. For LEO satellites, the common choices are a handheld or small directional yagi, such as an Arrow-style antenna, or a pair of crossed yagis with circular polarization on a az/el rotator. Circular polarization helps with spin and orientation changes of the satellite. A simple vertical will work on some passes but with deep fading and a poor low-angle gain trade-off.

Where would you spend the first budget increment: better coax, a better mount, or a higher-gain antenna? And what installation mistakes show up most often?

  • Replies 2
  • Views 56
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

For most installs the first money should go to the feedline and the mounting position. A 3 dB gain antenna on 100 ft of RG-58 at 70 cm can easily lose more than that gain in the cable. Dropping to a low-loss cable, or moving the radio closer to the antenna, often does more than swapping antennas.

The second thing is clearance. A collinear sitting right next to a mast, a gutter, a metal roof edge or a TV antenna will not have the pattern in the data sheet. On a vehicle the same applies: a 5/8 whip off-center on the roof will have a lopsided pattern, and a mag mount on a small flat spot will not behave like a roof-center NMO. The antenna can tune to 1.3:1 and still not perform well.

For J-poles, a simple choke on the coax near the feedpoint (ferrite beads, or several turns of coax in a coil) is cheap, and it can make the antenna's SWR less sensitive to cable placement. If the SWR shifts when you touch or move the coax, common-mode current is a likely cause.

  • Moderators

One thing worth separating is the type of use. For local FM simplex and repeater work, a vertical omni with moderate gain is usually the sensible choice. For weak-signal SSB, a horizontally polarized yagi is the norm, and for FM satellites you want something light and directional. Trying to cover all of these with one antenna ends in compromise.

On satellites specifically, circular polarization is not just a nicety. Since the satellite's orientation relative to you changes during a pass, a linear antenna can show deep fades. Crossed yagis fed for RHCP, or a simple directional antenna you can rotate in polarization by hand, helps. Also, for the satellite downlink on 70 cm, losses in coax and connectors matter just as much as at the repeater, so keep the run short and use N-type or another good connector at the antenna.

And on the SWR point: if the SWR meter looks great with a long thin coax run, test a short piece of the same cable through a dummy load. The reading will usually look 'good' because of cable loss, not because the antenna is efficient. An antenna analyzer at the feedpoint, or a known-loss check, is the quickest way to separate a bad match from a lossy line.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.