Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

First power-up of a homebrew QRP rig: what to check before the antenna goes on

ci_cover.jpg

Most dead kits and homebrew rigs fail in dull ways: a solder bridge, a backwards electrolytic, a toroid with the wrong turns count, or a missing ground. Whether it's a Pixie, a Tuna Tin 2 style crystal-controlled transmitter, a BITX-type SSB board or a uBITX, a fixed bring-up order saves a lot of time. This is a suggested sequence, and I'd like to hear where others would change it.

1. Cold checks. With the power off, check the supply rails to ground with a multimeter for a dead short. Look at the board under magnification for solder bridges, especially on fine-pitch headers and around the Si5351 or Arduino-style modules. Verify the polarity of electrolytics, diodes, and any transistor whose pinout differs from the one in your head. A series diode or a fuse on the supply input is cheap insurance against a reversed connector.

2. Current-limited first power. A bench supply with the current limit set just above the expected idle draw is ideal. If you don't have one, a small series resistor or a 12 V lamp in series with the supply will show a fault as a lit bulb instead of smoke. A Pixie-style rig should idle at a few milliamps. A transceiver with a display and microcontroller will draw far more, so read the build notes for the real figure instead of guessing.

3. Receiver before transmitter. Confirm audio first. A direct conversion receiver should produce a steady hiss and respond to a finger on the antenna input, with some hum or noise pickup. Then check that the local oscillator is actually running. A scope on the LO output is best. Otherwise, listen for the LO on a second receiver, with the antenna disconnected. Remember that a direct conversion receiver can radiate LO leakage and is prone to AM broadcast breakthrough and microphonics, so don't judge it only by whether signals come in.

4. Transmitter into a dummy load only. Use a proper 50 ohm load, not a random resistor on long leads. Power into a load is P = Vrms² / R. For 50 ohms, 1 W is about 7.1 V RMS (20 V peak to peak), and 5 W is about 15.8 V RMS (45 V peak to peak). A scope and a probe on the load will tell you roughly what you are making. Use an RF probe or detector if your scope bandwidth is marginal for the band.

5. Look at the spectrum, not just the waveform. A waveform that looks like a decent sine wave can still hide harmonics that are only 20 to 30 dB down. If you have an SDR, a spectrum analyzer or a second receiver, check the second and third harmonics, and check that your low-pass filter is the right one for the band in use. Class C and class E style stages in particular need a good filter. With multiband designs, a filter that is right for one band and wrong for another is a common problem, so check every band you plan to use.

6. Then the SWR bridge. A simple bridge or tandem match is most useful when calibrated with a known 50 ohm load for a null on reflected, then a short and an open for a full reflection reading. At QRP power, diode forward voltage drop makes the readings nonlinear, so treat an uncalibrated meter as a relative indicator rather than a precise measurement.

What would you move or add? In particular, how do you handle the very first transmit test when the only test gear is a multimeter and a dummy load?

  • Replies 2
  • Views 36
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

I'd put more weight on the dummy load. A badly made one can mislead you more than having none. A cluster of carbon resistors on short leads is fine at 5 W on HF, but a wirewound resistor can show reactance and give you strange SWR readings on the higher bands. If you're testing a 1 to 5 W rig, a few 100 ohm metal film resistors in parallel, with short leads and a decent ground plane, is an easy solution. Check it with the same bridge you plan to use for the rest of the testing.

Also keep the first key-down periods short. A resistor can get hot faster than you expect, and a transistor PA without enough heatsinking can drift or die before you have time to look at the scope. Key it for a second or two, check the DC current, then stop and look.

One more thing: if the DC current rises a lot but you see little RF on the load, don't just keep adjusting the trimmers. That usually points to the PA stage oscillating, a missing bypass capacitor, or a stage running without a proper load or bias.

  • Moderators

The cold checks are the best part of the list, and I'd add toroids to them. Many kit problems come down to winding. With a toroid, each pass of wire through the center counts as one turn, not each time the wire goes over the outside. Enamel also needs to be properly removed at the ends before soldering. A joint that looks shiny may not be making a connection through the insulation. Scraping, or using a hot iron with a little extra time on a pre-tinned wire end, solves it, and a continuity check across the winding confirms it.

For soldering generally, use flux-cored solder of a sensible gauge, a clean tip and enough heat to wet both the pad and the lead. Cold joints on ground connections are a classic cause of instability in low-power rigs. If a stage works only when you press on the board, reflow the nearby joints before you start changing component values.

On the minimum test gear question: a multimeter, a dummy load, and a second receiver or SDR to listen to what the transmitter is doing will take you a long way. A scope is better. A frequency counter is very useful for crystal or VFO work. But even the basic set lets you check supply current, the presence of RF, the transmit frequency and the harmonic content, which is most of what you need to know on day one.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.