Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a 24-hour EMCOMM field station: power budget, noise control, and setup/teardown order

ci_cover.jpg

I'm working through a design for a self-sufficient field station that could run roughly 24 hours without grid power. I want to sanity-check it before committing to gear. The target is one HF rig at 100 W, one dual-band VHF/UHF mobile, a laptop for digital messaging, LED lighting, and phone/tablet charging, all under a 10x10 canopy with a side wall or two.

The power side is a 12 V LiFePO4 battery, a small inverter generator as backup and charger source, and a folding solar panel for trickle support. For antennas I'm leaning toward a 33 ft fiberglass telescoping mast carrying an inverted-V dipole for 40 m, a separate dual-band vertical on a short mast for local simplex and repeaters, and a common-mode choke at each feedpoint.

The rough load budget is what worries me. Receive current is about 2 A for the HF rig, 0.8 A for the VHF/UHF rig, and 2 A for the laptop, plus about 1 A for lights. Add transmit at around 10 percent duty cycle on HF (about 20 A while keyed), and the average comes out near 7 to 8 A. That is more than 150 Ah per 24 hours, which is well beyond a single 100 Ah battery. Either the budget is too pessimistic or the plan needs either a bigger bank or scheduled generator charging.

Questions for anyone who has built a similar kit:

1. Is it better to size the battery for the full period and use the generator only as a recharge tool, or to run the generator continuously and keep the battery as a buffer?

2. How do you keep the generator, the charger, and the solar controller from wrecking your noise floor on HF?

3. What is your order of operations for setup and teardown so the mast, guy lines, and coax don't turn into a tangle when conditions change?

  • Replies 2
  • Views 45
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Your math is sound. The usual mistake is budgeting only transmit current when receive and ancillary loads are what drain the battery over a long deployment. A 100 Ah LiFePO4 battery is roughly 1,280 Wh nominal, and you shouldn't plan to use every watt-hour of it. For a true 24-hour run at your numbers you either want about 200 Ah, or you accept scheduled generator charging. Cutting the laptop's draw (screen dimming, a more efficient machine) is often the cheapest saving.

For the generator question, I'd lean toward running it in blocks rather than continuously. Inverter generators tend to be more fuel-efficient under a moderate load than at idle, so a decent DC charger pulling a steady load for a few hours is a better use of fuel than keeping it running for a 150 W station. You also get long quiet stretches for weak-signal work and for people sleeping. Pick a charger rated for LiFePO4 (typically around 14.2 to 14.6 V absorption), and don't assume an old lead-acid charger with an equalize or desulfation mode is safe for the bank.

A few practical points on distribution. Fuse close to the battery, then run everything through a fused distribution block with Anderson Powerpole-style connectors so polarity and pin orientation are standardized across the whole team. Check what your battery's BMS does at low voltage. Many simply disconnect, which drops the radios without warning, so a voltmeter on the bus helps you act before that happens. Also check low-temperature charge protection if there's any chance of near-freezing nights, because charging LiFePO4 below freezing damages the cells unless the battery has heating or a low-temperature cutoff.

For the generator itself: keep it well away from the shelter and downwind, never inside or under the canopy, and keep fuel stored and handled away from the operating area. Carbon monoxide is the real hazard here, and an enclosed or partly enclosed tent makes it worse. Treat it as a safety item on the checklist, not an afterthought.

  • Moderators

On noise: the most common culprits are switching supplies, not the generator engine itself. That means AC-DC converters, USB chargers, LED lights, laptop bricks, and MPPT solar controllers. Before you start anything, tune around the bands you intend to use and note the noise floor. Then bring things online one at a time (battery only, then solar controller, then generator and charger, then laptop and lights) and see what each one adds. That tells you what to relocate or replace instead of guessing. Distance is a cheap filter, so put chargers and controllers as far from the antenna and feedline as the cable lengths allow, and add clamp-on ferrites on DC leads where it helps.

For feedlines, a common-mode choke at the feedpoint keeps the coax shield from acting as part of the antenna and picking up noise from the shack. A second one near the radio end often helps as well. On 40 m, many people wind several turns of coax through a suitable ferrite core (31 mix is a typical choice for HF). Keep the coax run perpendicular to the antenna wire where practical, and don't coil excess coax right next to the shelter's power gear. Loss is minor at HF with decent coax, but on VHF/UHF a longer run of thin RG-58 will cost you several dB per 100 ft, so use a lower-loss cable like LMR-400 class for any real distance, or keep that antenna mounted close.

On grounding, separate the jobs. A single ground rod in dry soil does very little for RF and nothing for a direct lightning strike. What it can do is bleed off static and give you a common bonding point so all gear sits at the same potential. Bond the radios, supplies, and the coax shield entrance together, and keep the generator's grounding per its manual. The real lightning plan is behavioral: watch the sky, lower the mast and disconnect coax when storms approach, and stay away from the antenna. Also, plan the mast location for fall distance, at least the full height of the mast plus a margin from any overhead power line.

For setup order, one workable sequence is: site survey and layout (wind direction, generator downwind, mast clear of lines), shelter up and staked, mast and guys, antennas and feedlines with chokes, DC distribution and radios, then the generator and charging. Test on air and check noise before you commit to the layout. Teardown reverses it: power down and disconnect radios first, then lower the antennas, wind coax, collect stakes, and finally the generator after it has cooled. A photo of the stowed kit makes repacking much easier.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.