Winlink Express over radio: picking the mode, setting up the TNC or sound card, and avoiding the usual failures
- Replies 2
- Views 43
- Created
- Last Reply
Top Posters In This Topic
-
Mod_Chad 1 post
-
Mod_Chrissy 1 post
This thread is meant as a working checklist for getting Winlink Express from installed to actually passing traffic over RF. Details change between software versions, so check anything critical against the current Winlink documentation. The structure below should hold up anyway.
1. Account and passwords. Winlink Express asks for your callsign and a Winlink password on first run. The password belongs to your Winlink account on the central message servers. It is separate from any VARA registration key and from any passphrase you use elsewhere. A Telnet Winlink session over the internet is the easiest way to confirm the callsign and password are accepted before you try RF. If a radio session to a gateway fails at login, suspect the password first. Case, stray spaces, and an old password saved in another profile are common causes. Keep the password somewhere you can get to without the internet.
2. Pick the session type for the path you have. Telnet uses the internet and is good for testing and for checking forms. Packet Winlink uses AX.25 through a TNC, usually on VHF/UHF, to an RMS Packet gateway. VARA FM is a sound-card modem for VHF/UHF and generally runs much faster than 1200 baud packet where the path supports it. VARA HF and ARDOP are both sound-card modes for HF. VARA HF is faster on good paths but needs a registration to unlock full speed. ARDOP is free. Pactor needs a supported hardware modem, such as an SCS unit, and is still common among gateway operators. P2P is station-to-station with no gateway involved, and it works over packet, VARA, ARDOP, and Pactor.
3. Gateway selection. Update the channel list while you still have internet, because the list is cached locally. In the RMS channel selection window you can sort gateways by distance and, for HF, check propagation estimates. Treat the estimates as a guide and not a guarantee. When you set the radio, confirm whether the listed HF frequency is a center frequency or a dial frequency, and how your rig control handles it. With manual tuning in USB for a sound-card mode, the dial is typically set about 1500 Hz below the center frequency. Pick several candidate gateways on different frequencies and bands instead of relying on one.
4. Sound card basics. Use a dedicated audio path for the radio interface. In Windows, disable audio enhancements and keep system sounds off that device. On the radio, turn off speech processing and compression, leave noise reduction and DSP off or minimal, and keep the receive filter wide enough for the mode. Set transmit drive so there is no visible ALC action. Overdriven audio gives splatter and failed connections even when signal reports look fine. PTT can come from CAT, a serial RTS/DTR line, a CM108-type interface, or VOX as a last resort. Always listen first. The busy-channel detection in the modems helps but does not replace listening.
5. TNC setup for packet. With a hardware TNC, match the serial settings, KISS or terminal mode, and baud rate to what Winlink Express expects. With a software TNC such as Dire Wolf, you point Express at the TNC through an AGWPE-compatible or KISS interface and set the radio audio levels in the TNC. Keep the packet speed (1200 or 9600) consistent with the radio's data port and the gateway.
6. Forms and ICS-213. Winlink Express includes form templates, including ICS-213. A form opens in a browser, you fill it in, and when you submit it Express builds the message with the data attached, plus a readable text body. Update templates before a deployment, not during it. Keep messages short and avoid images, HTML bodies, and large attachments, since a few extra kilobytes can mean a very long session on a weak HF path. Check that the recipient can read the form, or at least the text body.
7. Radio-only and P2P. A radio-only message is one you want kept off the internet delivery path. Check the exact wording and behavior of that option in your version of Winlink Express before relying on it in an exercise. P2P needs no gateway. One station starts the session, the other is set to listen on the same mode and frequency, and messages move directly. Agree on the frequency, mode, and callsign or SSID in advance.
8. Practice. Winlink Wednesday is commonly used as a weekly practice exercise. Check the current instructions on the official Winlink site, because the exact format and addresses can change. Use that time to try a different gateway, mode, or form each week.
Which part do you find hardest to get stable: HF level setting, gateway choice, or packet TNC configuration?
Link to comment
https://www.hamradiobase.com/forums/topic/11147-winlink-express-over-radio-picking-the-mode-setting-up-the-tnc-or-sound-card-and-avoiding-the-usual-failures/Share on other sites