Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Repeater basics that trip people up: offsets, tones, linking and etiquette

ci_cover.jpg

This thread is meant as a plain-language checklist for newer repeater users, and for anyone who has had to explain the same things more than once. Please correct anything that varies by region. Repeater practice differs between countries, and sometimes between neighbouring clubs.

The first part is the setup that has to be right before you can hear or be heard. The repeater listens on one frequency (the input) and transmits on another (the output). Your radio transmits on the input and receives on the output. The gap between them is the offset, and it depends on the band. On 2 m it is commonly 600 kHz, with the sign (plus or minus) depending on where in the band you are. On 70 cm it is often 5 MHz in the US and 7.6 MHz in parts of IARU Region 1. Other bands use other values. Many radios apply an automatic offset by frequency, but that follows a default bandplan, not necessarily the repeater you want. Always check the listing.

Then there are access tones. CTCSS (often called PL, which is a Motorola trademark) is a continuous sub-audible tone between roughly 67 and 254 Hz. Many repeaters need it on your transmission before they will open. Some also send a tone on their output, and that tone can differ from the one they need on the input. DCS is a digital alternative that uses a three-digit octal code. Radios label these modes differently: "Tone" usually means encode only, "TSQL" means encode plus decode, and a cross-tone mode lets you set separate transmit and receive tones.

Etiquette is the other half. Listen first, and don't transmit over a conversation you can't hear because of a mismatched tone setting. Identify as your licence requires. Leave a gap between transmissions so others can break in. Respect the time-out timer, which cuts off long transmissions. Linked systems add a further consideration, because your audio may be heard on other repeaters or over the internet.

Questions for the thread: Which of these gets the most beginners into trouble? When someone says "I can hear it but it won't hear me," what do you check first? And how should a newcomer tell an open repeater from a closed one before keying up?

  • Replies 2
  • Views 37
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

For "I can hear it but it won't hear me," I'd work down the same list every time. First, is the offset direction right? Plus and minus are easy to get backwards. Second, is the transmit tone set, and is it the repeater's input tone and not its output tone? Third, is the radio on the correct mode, such as FM and not a digital mode with a similar-looking channel? Fourth, is there enough signal? Dropping to low power while testing can reveal a marginal path.

The reverse or input-monitor function is worth using. It temporarily listens on the repeater's input frequency. If you can hear the other station directly there, you may be able to talk simplex and leave the repeater free. If you hear nothing on the input but the repeater is strong, your path to the other station may depend on the repeater's better antenna.

Be careful with tone squelch on receive. It is useful for muting unwanted signals, but it can also hide a repeater that has changed its output tone, or a system that sends no tone at all. If a repeater seems dead, turn tone squelch off, or use the monitor key, and listen with the squelch open. The same advice applies to DCS. The code and its polarity (normal or inverted) have to match, and some radios hide the inversion setting in menus.

For time-out timers, the usual rule is to keep each transmission short and pause after the other station unkeys. Many repeaters send a courtesy tone to tell you the timer has reset. Hearing it before you key up is a good habit. Timer length and lockout behaviour are set by the repeater owner, so use the listing or club page as the reference, not a guess.

  • Moderators

Linking deserves its own etiquette section, because each system works differently and users sometimes assume they are all the same.

EchoLink is a voice-over-IP system. Licensed users are validated and connect to nodes and repeaters over the internet, so a connected repeater may carry audio from far outside your local coverage. IRLP and AllStarLink also tie repeaters to internet-based nodes. Each has its own commands, often sent as DTMF, and its own node numbering. Never send a command you don't understand on a linked repeater, because you may drop a link someone else wants or connect to a net already in progress. If a repeater's page lists a link schedule or command rules, follow them.

Digital repeaters add more settings. Wires-X uses Yaesu System Fusion, with connections made to nodes and rooms. DMR uses time slots, colour codes and talkgroups, and your radio needs a DMR ID and a correctly programmed contact and channel list. Programming the wrong talkgroup, or keying up on a busy one, is a common mistake. D-STAR relies on callsign routing fields and reflectors, so the MYCALL, UR, RPT1 and RPT2 fields need to be right. For all of these, read the network's or repeater owner's instructions. Many networks provide a test talkgroup or echo function, so check before you transmit into a busy group.

On open versus closed: an open repeater is available to any licensed amateur who follows the rules. A closed repeater limits access to members, who may be given a tone or code. Don't treat a published tone as permission to use a closed system. Directories such as RepeaterBook and club pages usually say whether a system is open or closed, but entries can be out of date, so confirm tone, offset and status with the club or owner. Coordination bodies and national societies also keep lists and help resolve interference, and many repeaters are funded by dues. If you use one often, joining the club that supports it is a sensible way to repay the owners.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.