Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

SSB audio chain: mic gain, ALC, compression and filters. What actually helps in weak-signal and DX work?

ci_cover.jpg

Starting a thread to collect practical SSB audio advice in one place. The goal is a signal that is easy to copy at the far end when the band is noisy, not one that merely sounds impressive on a local rag chew. Here is a framework to react to.

1. Start with the mic and how you use it. Most audio problems are fixed before the signal reaches the rig's processing. Keep a consistent distance from the mic, usually a few fingers' width. Speak slightly across the capsule rather than straight into it to cut plosives and breath noise. A foam windscreen or pop filter helps. Room echo and fan noise get transmitted too, so a quieter room beats a fancier equalizer. If you use a headset or desk mic, check that the rig's mic input type (dynamic or electret, bias on or off) matches the microphone.

2. Set mic gain with ALC, not by ear alone. On most rigs the ALC meter shows how hard the audio is driving the transmit chain. A common guideline is to adjust mic gain so that voice peaks move the ALC meter only to the edge of its working zone, or not at all on rigs where any ALC action is a warning. Check your manual, because meter behavior varies. Too much gain causes flat-topping, distortion and splatter. Remember that ALC is a protection circuit. Heavy ALC action is a sign of overdrive, not a way to gain more power.

3. Processor and compression: less than you think. A speech processor raises average power relative to peak power. That can help a weak signal stay readable, but only in moderation. Pushed hard, compression raises background noise, exaggerates sibilance, adds distortion and makes the signal fatiguing to copy. Many operators find that a few dB of compression is useful and that heavy settings give diminishing returns. Increase it gradually, and test with a monitor or a recording, not just the meter.

4. Use the monitor, but know what it tells you. Depending on the rig, the monitor circuit lets you hear your audio after the mic amp, equalizer and processing. That is useful for catching pops, hum, hiss and over-processing. It does not necessarily reveal what your RF signal looks like, such as splatter from an overdriven stage or a linear amplifier. For that, ask for a report from a station with a clean receiver, or look at your signal on a separate SDR or receiver. Use headphones so the monitor does not feed back into the mic.

5. Equalizer and transmit bandwidth. Many rigs allow you to set the transmit low and high cutoff, or choose a bandwidth such as narrow, medium or wide. A typical SSB transmission of about 2.4 to 2.7 kHz is enough for intelligibility. Removing very low frequencies, below roughly 100 to 200 Hz, reduces boominess and wasted power. A modest lift in the 1.5 to 3 kHz region can improve articulation, but boosting too much sounds harsh and invites distortion. Wider transmit audio sounds nice on a quiet band but uses more spectrum, which is less considerate on a crowded band and puts less power into the speech frequencies that matter for DX.

6. Upper or lower sideband. The usual convention is LSB on 160, 80 and 40 meters, and USB on 20 meters and up. On 60 meters, USB is the convention because of how the channels are used. Use the sideband the band expects, so people tuning across the band can find you. Operating on the wrong sideband mostly causes confusion, not a technical advantage.

7. Receive side: 2.4 kHz is a starting point. A roughly 2.4 kHz filter is a good general setting for SSB receive. For weak stations next to strong interference, you can often narrow to about 1.8 to 2.1 kHz, or shift the passband away from the splatter using IF shift or twin passband tuning. Narrower isn't always better, since the voice starts to sound muffled and you may lose readability. Noise reduction, notch filters and AGC speed all interact. For marginal signals, try turning off the preamp if the band noise already exceeds the receiver noise, reducing RF gain to keep strong signals from capturing the AGC, and trying a faster or slower AGC setting. Tune slowly. A weak SSB signal can be only a few hertz off and sound like Donald Duck.

8. Working DX and weak stations. Clarity and discipline count for more than raw loudness. Give your callsign clearly, using standard phonetics, and repeat it at an even pace. Don't call on top of a station you are still hearing, and listen for the DX station's split instructions. If they are working split, put your transmit VFO where they are listening and check that you are not on top of the pile. Keep your processing moderate so your signal remains clean under pileup conditions. Turn off the processor and reduce the drive if you notice splatter on a neighbor frequency.

Questions for the thread: what settings do you use for your own rig, and how do you test them? Does your processor help with real-world DX, or do you rely on a clean, lightly compressed signal? How do you decide when to narrow the receive filter?

  • Replies 2
  • Views 39
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One check that is easy to skip: record your own transmit audio, or ask a friend to record it, and listen to it later without the rig in front of you. Real-time monitoring is affected by what you hear in your headphones and in your head. A recording shows whether the compression is pumping the background noise up between words, whether the s sounds are too sharp, and whether the low end sounds boomy. It is also a good way to compare mic positions, because small changes in distance and angle can alter the sound more than a menu setting.

On ALC: the rule is not the same for every radio. Some rigs show a safe ALC range, while others also show compression level on a separate meter. If your radio has both, set mic gain first with the processor off, then add compression and re-check, because turning on the processor often raises the average level and changes how the ALC reads. Once you've set it, avoid readjusting it for every band. If one band sounds different, it is more likely a power setting, antenna mismatch or amplifier drive problem than the mic gain.

  • Moderators

On receive, I would separate two ideas: filter width and passband position. When the signal is weak but there is nothing next to it, a width of about 2.4 kHz often sounds natural and keeps the speech intelligible. When there is a strong signal on one side, shifting the passband can help more than shrinking the width, because you get rid of the interference without cutting out as much of the wanted voice. Narrowing the filter also cuts noise, but it affects tone, so use your ears and judge by readability rather than by how much quieter it sounds.

Also be careful with noise reduction. It can make weak speech sound smooth, but it can also add watery artifacts and hide the consonants that carry the callsign. For DX, try the filter and AGC adjustments first, then add NR only if it improves the copy. If a station is on the edge of the noise, copying the callsign matters more than making the audio pleasant, so a plain, slightly noisy receive signal may be better than a heavily processed one.

For transmit, the same logic applies. Under pileup conditions, a clean 2.4 kHz-ish signal with moderate compression and a clear callsign usually beats a wide, bass-heavy signal. The other station only needs to decode the information, not enjoy a broadcast-quality sound.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.