Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Rate vs. multipliers: how do you decide when to leave a good run frequency?

ci_cover.jpg

I'm building an operating plan for a weekend contest and want to compare notes on one decision: when to stay on a productive run frequency and when to go hunting. The usual advice is that running beats search and pounce for raw rate, but running has a ceiling. Once the callers thin out, the rate drops and you're paying for a frequency that no longer pays.

Here is how I'm thinking about it so far. In a contest where score is QSO points times multipliers, one new multiplier is worth roughly N/M of an average QSO, where N is your QSO count and M is your current multiplier count. At 2000 QSOs and 400 multipliers, a new multiplier is worth about 5 average QSOs. Early in the contest it's worth far less, and late in the contest it's worth far more. That suggests running hard early and shifting toward multiplier hunting as the weekend goes on, but I'm not sure that holds up in practice.

The questions I'd like input on:

1. What rate drop do you treat as the signal to move: 10-minute rate against 60-minute rate, or something else? Is there a point where you stop caring about the numbers and just go by feel?

2. For band changes, do you move on a schedule based on propagation, or react when the rate falls? In N1MM, the band-by-band rate and multiplier summaries make it easy to spot a band you've neglected, but I'm not sure how much to trust them against actual propagation knowledge.

3. With a skimmer or packet spots, how do you avoid chasing every new multiplier the moment it appears? Some spots are worth an immediate QSY and some can wait for a natural break in the run.

4. If you use SO2R, at what point does the second radio help your rate instead of just making the station busier? I've seen the argument that it only pays off if the run radio is already strong and the second radio is used for multipliers.

I'm also wondering how much of this depends on category. Assisted, unassisted, low power and high power all seem to change the answer.

  • Replies 2
  • Views 33
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the 10-minute versus 60-minute question, I'd treat the 10-minute rate as noisy and the 60-minute rate as slow. Short windows swing a lot because of a single pileup or a few dupes, so one bad ten minutes shouldn't send you off the frequency. A more useful trigger is a sustained drop plus a reason for it. If the rate is falling and you're seeing the same callsigns, or lots of dupes, the frequency is likely tapped out. If the rate is falling because of a fade or QRM, a band change or an antenna change may be the better fix.

Your N/M estimate is a good guide, but it has limits. It assumes the QSO and multiplier counts keep moving together, and it ignores how hard each one is to get. A multiplier you can work with one call on a bandmap is cheap. A multiplier that needs ten minutes of repeating your call into a pileup may not be worth it, even when the math says it is. I'd compare the expected cost in minutes against what you'd lose in rate over those same minutes.

On spots, the main thing is to sort them by value. A spot for a multiplier you still need on a band that's open right now is a candidate to work immediately. A spot for a multiplier you already have on another band might be better put off until you want to change bands anyway. Watch the spot's age and its signal-to-noise figure too. A skimmer spot with a decent SNR and several independent spotters is more reliable than a single manual spot with no corroboration.

Also check the rules for your category before leaning on any of this. Many contests treat outside spots, including Reverse Beacon Network spots, as assistance, and the treatment of a locally run decoder varies. Confirm that before you plan around it.

  • Moderators

On SO2R, I'd say most of the gain comes from reducing dead time rather than from running two radios at once. When you call CQ on radio 1, the gaps while you wait for callers are the time you can use on radio 2 to look for multipliers or check another band. That only works if the run radio is productive enough that you aren't constantly yanked away. If you're answering a caller every few seconds, there's no room to switch and the second radio just adds confusion.

The switching hardware matters more than people expect. An SO2R interface that handles transmit inhibit, audio routing and PTT correctly prevents a lot of mistakes. Good headset audio, with one radio in each ear or a way to latch and unlatch the audio, makes a big difference in how much focus you spend on keeping track of the radios. On the software side, N1MM's SO2R options let you decide how focus follows the radio you're transmitting on. Test those settings before the contest, not during.

Station design matters too. Two radios on the same band, or on bands with harmonic or overload problems, can hurt each other's receive. Band-pass filters, stubs and antenna separation are part of the plan, not an afterthought. If the antennas are close together, you may find the second radio is unusable on certain band pairs, and that should shape which bands you pair.

For fatigue, plan your rest in advance. A fixed break schedule is easier to stick to than deciding in the moment, especially when the rate is good and you don't want to leave. Hydration and food matter, and so does the practical question of when the bands are weakest. Taking your break during the lowest-rate hours costs less than taking it at peak. SO2R makes fatigue worse because of the extra mental load, so a casual SO2R stretch can feel harder than a steady run on one radio.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.