Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building a 5 W portable QRP setup: rigs, antennas, calling frequencies and LiFePO4 power

ci_cover.jpg

This thread is for sorting out what matters when you go low power. The idea is to compare notes on rigs, antennas and batteries, and to separate what really limits a QRP station from what only looks like it should.

First, the numbers. QRP is usually taken as 5 W output on CW and 10 W PEP on SSB. Those are the figures the QRP-ARCI contests use. The gap between 5 W and 100 W is 13 dB, a bit over two S-units. Most of us can recover that much with a better antenna, a better band choice or better timing, which is why QRP rewards antenna work more than almost anything else.

On rigs, the field runs from kits to complete radios. The Elecraft KX2 and KX3 are full multimode transceivers: CW, SSB, AM, FM and digital modes, with built-in options such as an ATU and internal batteries. Output is roughly 10 W on the KX2 and 10-15 W on the KX3, depending on supply voltage, so you can run 5 W or step up a little. At the lean end is the Mountain Topper series, CW-only 5 W rigs designed by Steve Weber KD1JV with SOTA in mind and very low current draw. The Penntek TR-35 is another compact CW transceiver kit. Check the current band options and specs with the supplier before ordering.

Then there are the simplest kits. Hendricks QRP Kits has long supplied small CW transceivers and receivers, and the Pixie circuit is the famous extreme: a crystal-controlled, few-component transceiver with a very basic receiver and a transmit power far below 5 W. The Pixie is a good first soldering project, but it is not good at sorting out crowded band segments. A direct-conversion or superhet kit teaches more about filtering and selectivity.

Questions to get started:

1. Which matters more to you, a multimode rig like the KX2/KX3 or a minimalist CW-only rig for hikes?
2. For antennas, are you using an end-fed half-wave with a 49:1 or 64:1 unun, a resonant linked dipole, or a loaded vertical with radials?
3. What are you using for power: SLA, LiPo, or LiFePO4?
4. Where do you listen first when you want to find other QRP stations?

For calling frequencies, the usual CW spots are 1.810, 3.560, 7.030, 14.060, 18.096, 21.060, 24.906 and 28.060 MHz, with 7.040 also used on 40 m. Commonly listed SSB QRP spots include 3.985, 7.285, 14.285 and 21.385 MHz. Band plans and regional practice differ, so check current lists for your region and for 30 m, where sources do not always agree. Calling frequencies are mainly places to meet. Once you make contact, move off the frequency.

  • Replies 2
  • Views 36
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On antennas, the most useful rule is to get the radiator up and in the clear first and worry about matching second. An end-fed half-wave on 40 through 10 m is popular for portable work because there is one wire, one transformer and a short run to a rig with a built-in ATU or a small external tuner. The trade-offs: the feedpoint impedance is very high, and the transformer's losses and the common-mode current on the feedline both reduce efficiency. A choke at the radio end can calm a rig that misbehaves with RF on the case or the key.

A resonant dipole or inverted V, fed with coax and a choke, is often a quieter and more efficient choice if you have a way to support the center. A linked dipole is simple to build: you move a few jumpers to change bands, and you can check it with an antenna analyzer or by looking at how far the SWR dips on each band. For SOTA or park activations, a lightweight 6 m or 7 m telescopic pole is usually enough support. A pole that is a little too short, with the wire as high as it will go, usually works better than long wires dropped near the ground.

With low power, take-off angle and local noise matter too. A low antenna can do well for nearby contacts on 40 m, while a higher one is better for long-haul DX. Choose the band for the time of day before you decide the antenna is at fault.

  • Moderators

On batteries, the key point is the voltage range your rig is built for. A 4S LiFePO4 pack is nominally 12.8 V and is usually charged to about 14.4-14.6 V. That fits many 12 V radios, but check the maximum input voltage in your manual. For example, the KX2 and KX3 documentation lists a maximum supply of about 15 V, so a freshly charged 4S pack is inside the range. Always check the manual for your own radio rather than assuming.

LiFePO4 has a flat discharge curve, so voltage stays steady through most of the pack's capacity and then drops quickly near the end. That helps a rig that sags under transmit load, but it also means a voltage meter tells you less about remaining capacity than it would on a lead-acid battery. A pack with a built-in BMS adds protection against over-discharge and short circuits. Even so, fuse the positive lead close to the battery, use polarity-protected connectors such as Powerpoles, and keep the wiring neat.

For capacity, calculate it instead of guessing. A rig drawing around 0.1-0.2 A on receive and 1-2 A on a 5 W CW transmit will average far less than its peak, since you spend most of the time listening. Compare a small pack's amp-hours against your planned operating time and add a margin, especially in cold weather, when most lithium chemistries lose usable capacity and charging below freezing can damage the cells. An accurate inline meter or the radio's own voltage display is the easiest way to tell how your station really behaves.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.