Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Small lot, one tall support, HOA rules: EFHW vs. doublet vs. inverted V vs. vertical for 80-10 m

ci_cover.jpg

Here is a scenario that comes up constantly. Take a lot with maybe 50 feet of usable width, one 30-35 ft support (a tree, a mast or a fiberglass pole), and a covenant that bans visible towers and beams. The goal is 40 m through 10 m with a decent shot at DX, and 80 m if it can be had. The question is which compromise does the least damage.

Before comparing wire shapes, two points are worth agreeing on. First, SWR tells you how well the load matches the transmitter. It says almost nothing about how much power ends up radiated. A dummy load has a perfect SWR and a terrible pattern. Second, on a small lot the real losses tend to hide in three places: the ground system (for verticals), the matching device or transformer, and common-mode current on the feedline. SWR on the shack side of the coax shows none of these.

The candidates, with my understanding of the trade-offs:

End-fed half-wave (EFHW). A 40 m version is roughly 64-67 ft of wire fed through a 49:1 or 64:1 transformer. It is resonant on 40, 20, 15 and 10 m as harmonics, which is why it is so easy to deploy with no tuner. Feedpoint impedance is in the low thousands of ohms, so transformer core material, turns and power rating decide how much power is lost as heat. There is no true balanced feed either, so the coax shield becomes part of the antenna unless you add a good common-mode choke near the transformer.

Doublet or G5RV-style. A center-fed wire with ladder line or window line, run into a tuner with a balanced output or a 4:1 balun. The line loss stays low even at high SWR, which is the main appeal. The tradeoffs are a tuner at the station and the need to route open-wire line away from metal, gutters and the house wiring. A G5RV is a doublet with a particular length (about 102 ft) and a short ladder-line section, and it is not magic on every band.

Inverted V. A dipole with the apex on the support and the ends sloping down. It is easy to hide, since the ends can run along a fence line. Resonant length is a little shorter than a flat-top and bandwidth is slightly wider. The pattern is fairly omnidirectional, and radiation depends heavily on apex height in wavelengths. At 30-35 ft, 40 m is around a quarter wave, which gives a lot of high-angle energy that is good for regional work but not ideal for DX.

Vertical. A vertical has a naturally low takeoff angle, but the efficiency depends on the radial field. A ground-mounted quarter-wave with only a few radials can lose a large share of power in ground resistance. Elevated resonant radials (several of them, cut for the band) tend to be more efficient per radial than buried ones, but they need to be placed where people will not trip on them.

Where would you start, and why? I am especially curious how people weigh a no-tuner multiband wire against a tuned doublet when the antenna is going to sit low and be hidden anyway.

  • Replies 2
  • Views 28
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the numbers, the first thing to settle is how much feedline you are dragging. RG-58 is on the order of 1.5 dB per 100 ft at 14 MHz and rises noticeably by 28 MHz, while RG-213 is roughly half that. A 100 ft run of thin coax into a mismatched antenna can quietly eat more power than people expect, because mismatch loss adds to the matched loss. Open-wire or window line on a doublet avoids this. Matched loss is a fraction of a dB per 100 ft, and it barely changes under high SWR. The tuner and balun then see the mismatch, which is the right place for it.

For a hidden antenna with a 30-35 ft support, I would think about the doublet or an inverted V with a short run of good coax. The EFHW is attractive because it is simple and light, and for a stealth install, a thin wire is hard to beat. But I would treat the transformer as a component to be chosen, not as a box. A 49:1 on a small toroid at 100 W SSB is fine. The same box on 100 W of FT8 or RTTY, which is near-continuous duty, can run hot. Core saturation and heating are real, and a choke at the feedpoint side matters, since the coax shield will carry some of the current whether you want it to or not.

For the vertical, the 'few radials' problem is not about SWR. You can get a vertical to show 1.3:1 with only two radials, and still lose much of your power in the soil. If space allows, 16 or more radials, even short ones, make a bigger difference than most feedpoint tweaks.

  • Moderators

I would add a point on common-mode current, since it explains why two antennas with the same SWR can behave so differently. With an EFHW, an OCFD or a G5RV fed with coax, the feedline can carry current on the outside of the shield. That causes RF in the shack, distorted patterns, and noise pickup from the house. A choke made from several turns of coax on a suitable ferrite core, or a stack of beads, at the feedpoint is cheap insurance. The goal is a high common-mode impedance across the bands you use, not a 'balun' label on the box.

On OCFD versus EFHW: an OCFD feeds at about one third of the length through a 4:1 current balun, so the feedpoint impedance is far lower than an EFHW and the transformer is under less stress. The cost is that the pattern on harmonics becomes lobed, and SWR is not always flat on every band. It is a compromise, like everything here.

I would also push back gently on the idea that the vertical is automatically the DX choice. On a small lot with limited radials, a well-placed dipole or inverted V that is high enough can match or beat it on many paths, simply because it wastes less power. A magnetic loop is the other option people mention for HOAs. It is quiet on receive and can be small, but the bandwidth is very narrow, you retune it when you change frequency, and efficiency falls on the lower bands when the loop is small compared to the wavelength. It suits 20 m and up better than 40 m and 80 m.

A NanoVNA or antenna analyzer helps, but for a fair comparison, use on-air reports, a WSPR or FT8 comparison on a schedule, or a noise-floor check. Impedance sweeps will not tell you how much goes into the sky.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.