Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

From FM birds to linear: how to plan a satellite station and handle Doppler across AO-91/92, SO-50, RS-44, ISS and QO-100

ci_cover.jpg

This is a discussion starter for anyone moving from terrestrial VHF/UHF into amateur satellites. The hobby is really three or four different skills, and it helps to separate them: predicting passes, pointing an antenna, managing Doppler, and operating with good habits on a shared transponder. Corrections and additions are welcome.

1. FM birds versus linear birds. FM satellites such as AO-91, AO-92 and SO-50 act like a repeater in the sky. They are single-channel, so only one QSO at a time works, and the footprint is large. Activity tends to be crowded, with short exchanges: callsign, grid square, signal report. Linear transponders such as RS-44 relay a whole slice of spectrum, so SSB and CW stations can share it. The transponder is inverting, so when you tune your uplink up, the downlink moves down. Frequencies, CTCSS tones and satellite status change over time, so check the AMSAT status pages and your tracking program's current Doppler data file before assuming anything from an old tutorial.

2. Doppler. For a LEO pass the shift scales with frequency. As a rough guide, you can see around ±3.5 kHz on 145 MHz and around ±10 kHz on 435 MHz, passing through zero at closest approach (TCA). On FM that is enough to make you miss your own downlink if you ignore it. On SSB and CW it matters even more, because a few hundred hertz changes how you sound. Gpredict and SatPC32 can both drive the radio's frequency through CAT control. A common approach is to pick the frequency you want on the transponder, let the software correct the uplink and downlink, and fine-tune by ear only when needed. If your radio can't be CAT-controlled, you can still do it manually with a tuning table, but it is much more work.

3. Gpredict versus SatPC32. Gpredict is cross-platform, with a good map and pass-prediction views and radio and rotator control. SatPC32 is Windows-only and has a long history with satellite operators. It works well with older rigs and lets you tweak Doppler memory settings in detail. Whichever you use, update your TLEs/Keps regularly and make sure your computer clock is accurate. Stale elements and a drifting clock are among the most common reasons a prediction looks "off" by a minute or two.

4. Antennas. A handheld Arrow-style dual-band Yagi is the classic entry-level setup. It is directional and light, and with a duplex-capable HT, or two radios, you can work FM birds. You point it by hand and adjust polarization by rotating it, since LEO satellites tumble or spin and signals fade. For linear birds like RS-44, a small crossed Yagi or a pair of separate 2 m and 70 cm Yagis helps with the weaker signals. Rotators (az/el) help a lot if you want to operate hands-free, but they add weight, wind loading, and calibration headaches. At higher elevations, elevation control matters, and low-loss coax matters too, especially on 70 cm.

5. ISS. The ISS offers APRS (digipeater on the standard 2 m APRS frequency) and, when enabled, a voice repeater and sometimes other modes. Its availability varies with crew schedules and equipment status, so check current ISS amateur radio status (ARISS) before planning a session. Treat the APRS digipeater as a shared resource: short packets, no spamming, and no assumptions that it is always on.

6. QO-100. QO-100 is different. It's geostationary, so there is no Doppler to chase and no pass planning. You get a fixed dish (with a suitable feed, LNB and transmit chain) and a narrowband transponder usable for SSB and CW. The difficulty shifts to frequency stability, because the 10 GHz downlink drifts if your LNB isn't stable, and to power control, since you must not overdrive the uplink. The community habit of keeping your downlink level in line with the beacon, rather than louder, keeps the transponder usable for everyone.

7. Grid squares. Most satellite contacts exchange Maidenhead grid locators. Knowing your four-character grid, and ideally six, saves time on the air. On FM passes, QSOs are fast, so be ready with your callsign and grid.

Questions for the group: What are you using for Doppler control, and why? For a first setup, would you point newcomers to an Arrow and an HT, or to a small fixed station with CAT? And on SSB/CW linear passes, what is your tuning routine when two stations land on the same frequency?

  • Replies 2
  • Views 31
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

For a first setup, I'd start with the Arrow and a full-duplex-capable rig or two receivers, then do a few passes with Gpredict or a phone app in listen-only mode. Listening to FM passes before transmitting is underrated. You hear how Doppler walks the downlink, how stations take turns, and how short the exchanges are.

One tip for FM birds: set your uplink and downlink memories in steps. Some operators work with a few memory channels spaced across the Doppler range rather than constantly spinning the dial, and just nudge the VFO as the pass goes on. If the satellite needs a CTCSS tone for access, double-check it against current AMSAT info. Tones and operating modes have changed on some birds over time.

For linear birds, I'd add that your downlink is the thing to fix first. Tune the downlink to hear a station, then adjust your uplink until you sound right in your own receiver. Don't try to correct both at once.

  • Moderators

On the rotator question, I'd think about the weight and wind loading first. A small az/el rotator that can only just carry a crossed Yagi tends to be a source of constant trouble. Calibrate north and the elevation endpoints carefully, then check that the software's pointing matches reality using a known geostationary target or a bright pass you can verify by signal peak. Also watch cable wrap and the 0/360 degree crossover, because some passes cross north and a poorly set rotator will swing the wrong way mid-pass.

On QO-100, the one thing newcomers often underestimate is that it is a completely different project: dish alignment, LNB stability and transmit-chain safety. If you are mostly interested in LEO, treat it as a second step, not a variation of the same station. If you do go for it, a stable LNB reference or software frequency correction against the beacon saves a lot of frustration on SSB.

For clashes on linear passes, I'd just listen, call briefly, and move a few hundred hertz if the pile-up is too thick. The transponder is wide enough for that, and it's far better than trying to out-power someone.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.