Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Getting the most from 5 watts: rigs, antennas, calling frequencies and LiFePO4 power for portable QRP

ci_cover.jpg

This thread is for the practical side of QRP: what makes a 5 W station work, which rigs suit which style of operating, and where the real gains are. Most of the gain comes from the antenna, the operating position and the operator, not the rig.

Definitions first. QRP is usually taken as 5 W output on CW and 10 W PEP on SSB. This is the figure QRP-ARCI uses for its operating awards and contests. Under 1 W is often called QRPp. The difference between 5 W and 100 W is about 13 dB, a little over two S-units at the usual 6 dB per S-unit. A dipole that is two S-units better than your last antenna gets you most of the way back.

Rig families people tend to compare.

  • Elecraft KX2 and KX3: full-featured multimode transceivers with CW, SSB and digital modes. The KX2 is the smaller one and covers 80 through 10 m. The KX3 is larger and also covers 6 m. Both are rated for a few watts to around 10 W depending on supply voltage and band, so check the current manual for exact figures. They are good all-rounders if you want SSB as well as CW and an internal ATU option.
  • Mountain Topper (MTR): a very compact, low-current CW rig built for summit activations. It uses a few fixed bands and is light and simple. Because it is CW-only, it suits operators who are comfortable with that.
  • Penntek TR-35: a single-band CW transceiver kit. Single-band designs are lean and efficient, but you need one rig per band or accept a limited choice of bands.
  • Hendricks-style and other small kits: good for learning what each stage does, since you can follow the signal path on the schematic as you build. Check the specifications of the specific kit you pick, such as sensitivity, selectivity and drift, because they vary a lot.
  • Pixie-type transceivers: extremely simple, with a crystal-controlled transmitter and a very basic receiver. They are a fun first build and a lesson in how little a CW transmitter needs. The receiver is not selective, so expect to hear a lot of the band at once. Treat them as a weekend project more than a daily driver.

QRP calling frequencies. The commonly used CW calling frequencies are approximately 1.810, 3.560, 7.030, 10.106, 14.060, 18.096, 21.060, 24.906 and 28.060 MHz. Commonly cited SSB calling frequencies include roughly 3.985, 7.285, 14.285, 21.385 and 28.885 MHz. These are conventions, not reserved channels, and they depend on your region and band plan. Check the plan that applies to you, and listen before calling. If nobody is on the frequency you can call CQ QRP there, and if a QRO station is nearby, move up or down a bit.

QRP-ARCI. The QRP Amateur Radio Club International publishes a journal and sponsors contests and awards built around the 5 W and 10 W PEP definitions. If you want a reason to be on the air with a small rig, club operating events and sprints give you plenty of QRP stations to work, and exchanges that include your power level.

Antennas for low power. A resonant antenna fed with low-loss coax is hard to beat. Common portable choices:

  • Half-wave dipole or inverted V on a lightweight mast or in a tree. Even a modest height of 5 to 10 m or more is a big step up from a vertical right at ground level.
  • End-fed half-wave (EFHW) with a matching transformer, popular because it needs only one support and one feedpoint, and works on the fundamental plus harmonics.
  • Linked dipoles, where you change band by moving a jumper, which avoid tuner losses.
  • Random wire with a counterpoise and a tuner, which is flexible but depends on a good counterpoise, and losses in the tuner and matching network can be significant at QRP.

At 5 W you can't afford much loss in the feedline and matching, so keep coax short and good, and keep SWR reasonable at the antenna rather than just at the rig.

Battery and LiFePO4 power. A 4S LiFePO4 pack has a nominal voltage of about 12.8 V, with a charged voltage up to roughly 14.4 to 14.6 V, and it holds a fairly flat voltage through most of the discharge. That suits transceivers that like 12 to 13.8 V. Make sure your rig's maximum input voltage is above a fully charged pack, and fuse the positive lead close to the battery. Compare 3S LiPo, which can sag differently and has its own safety needs. Capacity math is simple: a rig drawing, say, 2 A on transmit and much less on receive can run for hours from a few amp-hours, since most of your time is spent listening.

Questions to get things going: what is your best bang-for-the-gram setup for summit work? Do you prefer a multiband rig and tuner or a single-band rig and a resonant antenna? And what is the smallest battery you consider reliable for an afternoon of operating?

  • Replies 2
  • Views 32
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the multiband versus single-band question, it often comes down to what you are willing to carry. A multiband rig like a KX2 with an ATU gives you flexibility, but if you are going to a park with a resonant EFHW or a linked dipole, you may not need the tuner at all. A single-band rig with a matched antenna reduces both weight and things to go wrong.

One caution on voltage: check your pack's fully charged voltage against the rig's rating. A 4S LiFePO4 pack charged to the top is usually fine for 12 V gear, but a rig with a tight upper limit might not be. Also note that rated output often drops at lower supply voltage, so a rig quoted at 10 W at 13.8 V will give less from a sagging pack. Test it on the bench with a power meter and a dummy load before you rely on it in the field.

  • Administrators

For anyone starting out with kits, I would separate two goals: learning to build, and having a good radio. A Pixie-style rig is great for the first, but its receiver is so broad that it can be frustrating for the second. If you want a first contact with a kit you build yourself, look at something with a proper superhet receiver and a narrow filter, and keep the Pixie as a fun side project.

On calling frequencies, listen for a while before you call. Many QRP stations tune up and down the calling frequency instead of sitting on it, and a CQ on 7.030 or 14.060 will get answers more often than a CQ in the middle of a crowded segment. Sending your power in the exchange, such as 5W, tells the other operator that you are running QRP, and good operators will often slow down and repeat. If you are chasing QRP-ARCI-style events, keep a log of both the power you ran and the power the other station reported, since that is how the scoring typically works.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.