Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Before buying a new HF rig: grounding, bonding and common-mode fixes that decide how any radio behaves in your shack

ci_cover.jpg

Whether the radio on the desk is an IC-7300, IC-7610, FT-991A, FTDX10, TS-590SG, TS-890S, K3S, KX3 or a Xiegu G90, many of the problems people blame on the rig come from the station around it. Typical symptoms are RF in the audio, a CAT or USB link that drops when you key up, a noisy receive floor, a tuner that behaves strangely, and an amplifier that trips on high SWR. This thread is meant to sort out the order of operations: what to fix first, and what really depends on which transceiver you own.

1. Keep three grounds separate in your head. Safety bonding (the mains equipment ground and the bonding of metal enclosures), lightning protection (a path to earth outside the building, bonded to the electrical service ground per your local code) and RF grounding are three different jobs. A ground rod by the operating desk does not make an antenna system work better, and a long wire to it can make RF problems worse because it is just another resonant conductor. Check your local electrical code, and if the work touches the mains service, involve a qualified electrician.

2. Common-mode current is the usual culprit. RF travelling on the outside of the coax shield, on USB leads, on audio cables and on the DC supply leads is what gets into microphones, interfaces and keyboards. The first line of defense is a good common-mode choke (a current balun or a stack of suitable ferrite cores) at the antenna feedpoint, and often a second one where the coax enters the shack. Choke impedance depends on the ferrite mix and the band. A choke that works on 20 m may do little on 160 m, so match the mix and number of turns to the bands where you have trouble.

3. Power supply. A 100 W class rig at 13.8 V can draw roughly 20 A or more on SSB or CW peaks, so a 25 to 30 A supply gives comfortable margin, especially if you add an amplifier driver or other 12 V gear. Use short, adequately heavy DC leads, fused at the supply, and keep the connections tight. Some switching supplies put noise on the HF bands. If you hear birdies or a raised noise floor that changes when you power the supply from a different outlet, or disappears on battery, the supply is the first suspect. Ferrites on the DC leads, a different supply or a linear supply are the usual remedies. A KX3 or G90 running on a battery avoids a lot of this.

4. Tuner placement matters as much as the tuner. The internal ATU on most of these rigs, and external tuners, match the radio to the line. They do not change the SWR on the coax between the tuner and the antenna. With a high-SWR feed line, loss goes up and so does common-mode current, so a tuner at the radio can make a bad antenna usable without making it efficient. Many people with non-resonant antennas get a better result from a remote tuner at the feedpoint or from a properly designed balanced feed line system.

5. Band-pass filters and receivers. BPFs earn their keep when you operate more than one transmitter on different bands close together, run contests with multi-station setups, or live near a strong broadcast, AM or other transmitter. Direct-sampling radios (IC-7300, IC-7610) and hybrid or superhet designs like the FTDX10, TS-890S, K3S and FT-991A handle strong signals differently, but none of them is immune to an overloaded front end. If a preamp or attenuator setting changes the problem, front-end overload is likely. A BPF on the receive path, or an attenuator, is cheaper than switching radios.

6. Amplifier interfacing. Set the drive level to what the amp needs and not to the rig's maximum. Check ALC behavior, and check that the keying line and band data are wired correctly before the first transmission. Where an amp has a poor ground reference or the RF cable shields are unbonded, feedback is common. Leave a gap between the amp and the radio's control cables, and keep USB and audio runs away from the RF output cables.

7. Layout. Keep RF cables away from the computer, USB hubs and monitors. Use short, good-quality USB cables with ferrites on both ends, and consider a USB isolator for CAT and audio if ground loops are present. Bond equipment chassis together with a short, wide strap or a common bonding bar for safety and for a defined reference, then route the station through a single entry panel where lightning arrestors, if used, are bonded to the outside ground system.

What order do people usually tackle this in, and which of these steps made the biggest difference on different radios?

  • Replies 2
  • Views 31
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One way to order the work is by cost and by how much each step tells you. Start with a feedpoint choke and a check of what the coax is doing (a clamp-on RF current meter or just seeing whether touching the shield changes the symptom). It's cheap, and if the problem moves or goes away you've learned that it was common mode and not the radio.

On the rig side, the differences are real but smaller than people think. The IC-7610 has two receivers and good dynamic range, the K3S is known for strong receiver performance and the ability to add filters, and the TS-890S is aimed at similar strong-signal performance. But all of them can be disrupted by a noisy supply, an unbalanced antenna system or an overloaded front end from a nearby transmitter. So a new radio on the same coax and the same cabling can show the same problems. If you do change rigs, change one thing at a time, otherwise you can't tell whether the result came from the radio or from the rewired shack.

  • Moderators

I'd add a note on the lower-power and portable gear. A KX3 or G90 is often run from a battery or a small supply, which removes the supply-noise variable, but the antenna still has the same common-mode issues, and an end-fed or random wire with a tuner makes the coax shield part of the antenna if there is no counterpoise or choke. For those setups a choke at the tuner output and a deliberate counterpoise often help more than adding a ground rod.

On bonding, remember that the point of tying equipment together is a defined, low-impedance reference and safety if a fault occurs. It isn't a way to drain RF out of the shack. A short strap between the radio, tuner and amp is fine. A long wire to a distant stake makes a poor RF path at HF, and it could carry RF back in. If you are adding lightning protection, the entry panel and its connection to the service ground are the part to get right, and a local electrician or the electrical code is the authority on that, not forum rules of thumb.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.