Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Repeater setup and etiquette checklist: offsets, tones, linking, and the mistakes worth avoiding

ci_cover.jpg

A lot of repeater problems come from the same few settings and habits, so this thread collects them in one place. Add corrections, local differences and anything I've missed.

Offsets. The offset is the gap between the repeater's output (what you hear) and its input (what you transmit). Offsets follow the band plan for your region, so check it. In the US, 2 meters usually uses 600 kHz, positive or negative depending on where the output sits in the band. 70 cm usually uses 5 MHz. 1.25 m is usually -1.6 MHz. Europe commonly uses 600 kHz on 2 m and 7.6 MHz on 70 cm. A repeater that seems to be "just noise" often has the offset direction wrong. Always program from a trusted listing and confirm with the owner or club.

CTCSS, PL and DCS. CTCSS is a continuous sub-audible tone, roughly 67 to 254 Hz, sent along with your voice. "PL" is Motorola's trade name for the same thing. Many repeaters need the right tone on your transmit side before they will open. Some also send a tone on the output, and your radio can use that for tone squelch. If you only want to hear transmissions from that repeater, set the receive side to match. DCS does a similar job with a digital code instead of an audio tone. Mismatched polarity (N versus I) is a common reason a DCS code fails.

Remember that a tone is not security. It only controls access and cuts interference. Tone squelch on receive can also hide a problem: if you hear nothing, you may not know whether the repeater is idle or your decode setting is wrong. When you troubleshoot, temporarily set receive to carrier squelch.

Timers and pacing. Most repeaters have a time-out timer, often somewhere between one and three minutes, that drops the repeater if one transmission runs too long. Even without that, leave a short gap between overs. It lets other stations break in and lets the courtesy tone do its job. On a linked system, give extra time for delay across the links.

Open or closed. An open repeater welcomes any licensed amateur within the rules. A closed repeater limits use to members or to people who have been given the access details. Don't assume an unlisted tone means a repeater is open to everyone. Ask the trustee or club if you're unsure. Coordination matters here too. In many regions a volunteer coordinating body assigns pairs to reduce interference, and coordinated repeaters usually get priority in disputes. Check your own country's rules for the details.

Linking. Repeaters can be tied to other systems in several ways:

EchoLink uses VoIP and validates callsigns. IRLP uses node numbers and reflectors. AllStar is built on Asterisk and uses numbered nodes and hubs. Wires-X connects Yaesu System Fusion nodes through rooms. DMR uses talkgroups, time slots and color codes, and you need a DMR ID. D-STAR uses reflectors and routing fields, and its reflector modules are lettered. Each system has its own rules for keying up, connecting and disconnecting. Listen to the link for a while, and don't key into a busy talkgroup or reflector without knowing who is on it.

Basic etiquette. Listen before you transmit. Identify as your rules require, and keep transmissions short. Avoid kerchunking, which means keying the repeater just to test it. On a linked repeater, assume people elsewhere can hear you. If you're calling, say your callsign plus "listening" or "monitoring" rather than a long CQ call. Net traffic and emergency communications take priority.

Finding repeaters. Directories such as RepeaterBook and regional coordinator lists are good starting points. Club websites often have the most current details on access and linking. Any listing can be outdated, so confirm before you depend on it.

What settings or habits cause the most trouble where you operate?

  • Replies 2
  • Views 36
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One addition on tones: when you set a repeater's tone in the radio, make sure you know which field you're editing. Many handhelds have separate settings for encode only (tone), tone squelch (decode too) and DCS. Choosing "Tone" when you meant "TSQL" is a very easy mistake. If you can't open the repeater, check that the offset direction is right, the tone is entered on transmit, and the radio really is in the mode you think it is. Test with a second radio or a monitor if you can.

On digital repeaters the equivalent checks are different. For DMR, check the color code, time slot and talkgroup. For D-STAR, check that the repeater callsign fields are set correctly. For Fusion, check that your radio's squelch mode matches the repeater's.

  • Moderators

On linked systems, I'd stress the pause. Even with a fast link the audio can arrive late, and a quick "break" may be missed. Leaving a bit more space than you would on a local repeater gives others time to jump in. The same applies if a net is running: wait for the net control to acknowledge you.

Another practical point is to find the repeater's own page or club contact before you start using its linking features. Some owners disable remote connections, restrict who can issue commands, or limit what can be linked at certain times. Linked repeaters can also carry traffic from far away, so a call that makes sense locally may not be useful to everyone listening. Etiquette follows the system as well as the band.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.