Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a 24-hour EMCOMM field station: generator, LiFePO4, solar, and where noise and grounding bite

ci_cover.jpg

I'm putting together a power and station plan for a 24-hour served-agency support deployment, and I want to sanity-check the design before it turns into a checklist. The setup is a tent or pop-up shelter, one HF transceiver at 100 W, one VHF/UHF mobile for local nets, a laptop for logging and digital modes, a few LED lights, and phone and tablet charging. A small inverter generator is available as a backup. The main power would be a LiFePO4 battery with some solar to extend it.

Here is the rough power math I'm working from, so please correct it. A 100 Ah LiFePO4 battery holds about 1,280 Wh nominal, and with some reserve for the BMS you might count on about 1,000 to 1,100 Wh. If the station averages around 6 A at roughly 13.2 V (receive, an occasional SSB transmission, the laptop and lights), that is about 80 W, or roughly 12 to 14 hours. That is tight for 24 hours, which is why I'm weighing solar against a generator for topping up. Transmit current on a 100 W rig can peak near 20 A, so the wiring and fusing have to be sized for that peak and not for the average.

These are the points where I'm least sure of the right approach:

1. Noise. Inverter generators, cheap PWM solar controllers, USB chargers and LED lights can all raise the HF noise floor. My plan is to tune to a quiet spot on 40 m or 20 m with only the receiver on, then bring each device up one at a time and note the S-meter change. Is there a better way to do this?

2. Grounding. For a temporary station with no lightning protection, I'm treating grounding as mainly about safety and keeping RF out of the shack. I'm thinking of a common bond point for the radios and power distribution, plus a current choke at the antenna feedpoint. Where does a ground rod help, and where does it only add a false sense of security?

3. Coax and masts. For a fiberglass mast with an inverted-V or EFHW, I'm planning on 50 ft of coax at HF and a shorter, lower-loss run for VHF/UHF. I'm trying to decide how much strain relief, drip-loop and cable-routing effort is worth it before the footprint gets cluttered.

Please poke holes in any of this. I'd especially like to hear from anyone who has run a similar setup about what they would change in the order of operations at setup and teardown.

  • Replies 2
  • Views 27
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Your power math is reasonable, but I'd budget for the battery chemistry's behavior as well as its capacity. LiFePO4 holds a fairly flat voltage, around 13.2 to 13.3 V under modest load, then falls off quickly near the end. Many batteries also have a BMS that disconnects abruptly at its low-voltage or overcurrent limit, so the radio doesn't gradually fade, it just goes dark in the middle of a net. A small DC voltmeter or shunt-based monitor at the distribution block is worth having, and so is a plan to swap or recharge before you are down to the last 10 to 15 percent. Also check that the BMS continuous rating covers your peak draw with margin once the 100 W rig and anything else on the bus are all running.

For wiring, fuse close to the battery terminal, use a fused distribution block with each branch protected for its wire gauge, and keep high-current runs short. 12 AWG is usually fine for a 20 A radio feed over a short run, but check the voltage drop at the radio when transmitting. A radio that sees 12 V on peaks may distort or fold back power, and it will look like an antenna problem. Whatever Powerpole orientation your group uses, label it on every cable, because the mistake you're guarding against is reversed polarity from a borrowed cable.

One more caution on solar: LiFePO4 should not be charged below freezing unless the battery has low-temperature charge protection or a heater. Cold-weather deployments need either that or a different plan. And make sure the controller has a lithium profile, not just a generic setting for lead-acid.

  • Moderators

On noise, your one-at-a-time test is the right idea, and I'd add a few refinements. Run it on the bands you actually expect to use, not only one, because switching noise from a controller or charger tends to show up as combs of birdies and may be bad on 80/40 and clean on 20. Test with the antenna you'll deploy, since a small receive-only loop or a short whip may not show the problem a full-size wire does. Do it with the generator running as well as on battery, since the generator's own radiated noise and its distance from the antenna are part of the picture.

With generators generally, distance and placement are the cheapest fixes. Put it well away from the shelter, downwind, and keep it from sitting under the antenna or beside the feedline. Carbon monoxide matters at least as much as RF: never run one in or right next to a tent or shelter, and a battery-powered CO alarm is cheap insurance for any occupied space. Take a look at the manual too, since bonding and grounding instructions differ between models, and don't assume a ground rod is required or forbidden for a cord-fed portable unit.

For grounding in the field, I think your framing is right. A ground rod doesn't give you meaningful lightning protection. If a storm is near, the usual practice is to stop operating, disconnect the antennas from the radios, lower masts if you can do so safely, and shelter away from the equipment. For RF, the bigger gain is usually a 1:1 current choke at the feedpoint and maybe another near the radio, which keeps common-mode current off the coax shield and out of your station. Bond the equipment ground points together so you don't have two grounds at different potentials. Keep masts and guy lines well clear of overhead power lines, with margin beyond the mast's full height, and don't raise one in rising wind. Coax-wise, at HF the loss difference between decent 50 ft runs is small, so spend your effort on VHF/UHF, where lower-loss cable pays off.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.