Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

No TX and no RX on the same rig: what do you check first, and in what order?

ci_cover.jpg

A rig that is dead on both transmit and receive is usually less mysterious than it looks, because the two paths share a lot: DC power, the master oscillator and PLL, the control logic, the antenna connector and sometimes the T/R relay. That makes it worth working from the common parts outward instead of jumping to the finals. I'd like to compare approaches, so here is a rough order of attack and a few places where people commonly go wrong.

Step one is power, measured at the rig and not at the supply. Check the fuses in the DC cable (both legs on many rigs) and look at the connector for heat discoloration or a loose pin. Then measure the voltage at the radio's own DC input while it is switched on and, ideally, while it is transmitting. A supply that reads 13.8 V unloaded and sags to 10 V when asked for 20 A will make a rig behave as if it were broken. A dead display with a good-looking supply voltage often points to a failed internal regulator or a bad power switch, so trace the rails the service manual lists (typically 5 V, 8 V, 9 V and the switched 13.8 V line).

Step two is to decide whether it is really dead or just muted. Many rigs that seem to have no receive are actually fine in the RF section and fail in the audio path. Turn up the AF gain, open the squelch, disable noise reduction, try headphones and an external speaker, and see whether you hear any noise floor at all. Switch off the preamp and attenuator and check the antenna relay or PIN diode switching if there is one. A healthy receiver with the antenna disconnected usually has a different noise character from a dead one. If you hear nothing, even hiss, the fault is probably after the detector or in the audio amplifier. If you hear hiss but no signals, look at the PLL lock, the first mixer and the filters, and confirm the reference oscillator is running.

Step three is transmit, with a dummy load and a wattmeter, never an antenna. Check whether the rig draws any current at all in transmit, and watch for sudden current limiting. Many modern rigs have SWR or current protection that folds back power or refuses to key. A fault in the SWR bridge, a bad detector diode, a dried-out capacitor or a cracked solder joint on the forward and reflected sensing can trip protection even into a perfect load. If the rig shows high SWR into a known good dummy load, do not assume the finals are bad; measure the DC outputs of the sensing circuit against the service manual.

Finals deserve respect, because they are rarely the root cause. If a PA transistor has failed, ask why it failed: high SWR, parasitic oscillation, an overvoltage event, a wrong bias setting, a failed driver, a bad heatsink contact or a failed protection circuit. Replacing the device without finding the cause tends to produce another dead device. Before replacing, check the bias network, the bias resistors and diodes or thermistors, the drain/collector chokes, the output filter capacitors and the DC feed. Reapply thermal compound properly, and set bias as the manual specifies, typically with a current meter in the supply line.

Capacitors, contacts and alignment are the other big areas. Electrolytics age, especially in supplies and in SMD electrolytics on older boards that can leak and corrode traces; replace with the same value and at least the same voltage, ideally a 105 °C low-ESR type, and clean any residue off the board. An ESR meter is much more helpful than a capacitance reading alone. Contact cleaner and isopropyl alcohol help with intermittent switches, connectors, relays and pots, but use them sparingly and only where the manual or common sense says it is safe. Do not touch alignment adjustments until you know the fault is not something simpler. Alignment needs the manual, a stable signal source, a frequency counter, a dummy load and care; mark or note the original positions first.

What is your preferred first test when a rig appears to be dead on all modes? Do you start with the supply, the fuses, or with a quick current-draw check on a current-limited bench supply?

  • Replies 2
  • Views 27
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

A current-limited bench supply is a good start, and I'd lean on it more than the first post does. Set the current limit conservatively, bring the voltage up and watch the standby current. If the rig draws almost nothing, you are probably looking at a missing rail, a failed power switch or a blown internal fuse. If it draws far more than the manual's standby figure, something is shorted or a regulator or capacitor has failed. That is much better than finding out with a big, unlimited supply that happily feeds a short until a track burns.

On the SWR protection point: when a rig folds back power into a dummy load, I would check the dummy load itself and the coax jumper with a multimeter before opening the case. A cheap dummy load that is out of its range at higher frequencies, or a jumper with a bad center pin, can show high SWR on one band and look fine on another. If the same fault appears on every band into a known good load, then it is worth tracing the forward and reflected detector circuit.

I'd also add that a DMM in the DC supply line is useful during bias setup, but check the meter's current range and fuse rating first. A 10 A meter range that is not actually fused for the 20 A the rig can draw is a bad surprise waiting to happen.

  • Moderators

For the scope side, the most useful thing is probing the signal chain in a sensible order rather than randomly. On a receiver you can inject a known signal from a generator and follow it with a scope or an RF probe stage by stage, from the antenna connector through the filters and mixer to the IF and detector, until it vanishes. On the transmit side, a scope with a proper attenuating probe at the PA output into a dummy load shows you the waveform, and flat-topping or distortion is a clue to bias or supply problems. If you want to check for oscillation or harmonics, a spectrum analyzer or a well-set-up SDR with a suitable attenuator and a proper sampler can show more than a scope, but never connect a transmitter directly to an SDR input.

On the capacitor topic, I'd stress that a part that measures its nominal capacitance on a cheap meter can still be bad. Electrolytics with high ESR can cause ripple on supply rails, which shows up as hum, hash or a rig that resets only on transmit peaks. If you see ripple on the scope at a rail that should be clean, treat the capacitors near that rail as suspects before looking at the semiconductors.

Finally, keep the service manual open and compare measured voltages with the stated test points. If you don't have the manual, look for the block diagram first, even a generic one for the same family of rig. A schematic tells you what the circuit should look like, and that is half of the diagnostic work.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.