Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Remote station design compared: radio-native LAN (IC-7610/RS-BA1, SCU-LAN10), Flex, RigPi and SDR receivers, plus security, latency and licensing

ci_cover.jpg

Remote operation questions usually start with "which box do I buy?", but the choice makes more sense once you split the problem into layers. A remote station has a control path (CAT/frequency/mode/PTT), an audio path (RX and TX), station support (power switching, antenna switching, amplifier, rotator, cameras, SWR and temperature monitoring), and a network path that connects it all to you. Different products handle these layers differently, so this thread is a place to compare approaches and sort out which layer each one covers.

Radio-native LAN control. The Icom IC-7610 has a network port and works with Icom's RS-BA1 remote software, so the radio itself serves control and audio over IP. Third-party clients such as wfview also speak Icom's network protocol. Icom has used a small group of UDP ports (commonly listed as 50001 to 50003 for control, serial and audio), but check your radio's menu and manual instead of trusting a forum post. Yaesu's SCU-LAN10 takes a different route: it is a separate interface unit that puts supported radios' control and audio onto a LAN. Compatibility is model-specific, so verify your exact radio and firmware before you buy. In both cases the radio's remote features were designed for a trusted network, which matters for the security section below.

Flex. SmartSDR with SmartLink is the usual remote route for FlexRadio's networked radios. The radio is effectively a server and the client can be anywhere, so the radio's own panadapter and slices are available remotely. That is a real advantage over a CAT-and-audio-only link, because you see the same spectrum you would see locally. Confirm what your radio generation and licensing require, and what SmartLink needs from your router.

RigPi and similar Raspberry Pi controllers. A Pi-based station server (RigPi is one example) sits between the radio and the network and typically uses Hamlib-style rig control with a web interface and some station-accessory control. Its value is less about audio magic and more about giving you one consistent place for rig control, relays and accessories, independent of the radio brand. Audio transport and the TX/RX workflow depend on the software you pair it with.

Receive-only helpers: KiwiSDR and WebSDR. A KiwiSDR is a wideband HF receiver (roughly 0 to 30 MHz) shared through a browser. WebSDR is a separate system, originally from the University of Twente, with many independent sites. Neither transmits, so they are not a remote base. They are useful for something else: checking your own signal. If a public receiver near your remote site hears you, you have an independent check on audio quality, frequency and propagation, so you are not relying only on the link you built. Also respect each site's user limits and etiquette.

Hosted and shared services. RemoteHams.com and similar services are about connecting operators with remote-capable stations or SDR access. Details such as availability, who controls the transmitter, and what an operator needs to be licensed for differ by service and change over time, so read the current documentation instead of relying on a summary here.

Network security. Please do not just forward the radio's UDP ports to the internet. A safer pattern is a VPN (WireGuard, OpenVPN or an overlay network) so only an authenticated device can reach the radio network. This also helps if your ISP uses CGNAT and port forwarding is impossible. Put the shack gear on its own VLAN or subnet, disable UPnP, change default passwords, keep firmware current, and log connections. Remember that a compromised remote link can mean unauthorized transmissions under your callsign.

Latency and jitter. One-way latency of tens to a couple of hundred milliseconds is workable for SSB, but jitter and packet loss do the damage: choppy audio, PTT hang, delayed unkey. CW is the tricky case because keying over a delayed link ruins timing. Send CW as text or keyer commands to a keyer at the remote end, not as raw key-down events. FT8 and other timed digital modes should run the decoder and clock at the radio site so network delay doesn't matter. Pileups and QSK-style work are where the delay is most noticeable.

Rules. The legal answers depend on where the station is and where you are. Generally the control operator must be able to turn the transmitter off, and the station must be identified and operate within the licence of whoever is in control. In many countries remote control is allowed but may carry extra conditions, and operating a remote station in a different country can raise licence issues. Contests and awards (including DXCC-style programs) have their own rules about remote stations, so read the current version for the one you care about. Ask your national regulator if the wording is unclear.

What combination are you weighing, and where are you most worried: security, latency or the rules?

  • Replies 2
  • Views 26
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One design point that gets overlooked is the failure mode. If the link drops mid-transmission, what stops the transmitter? A solid remote station assumes the network will fail eventually. Useful safeguards are a watchdog that drops PTT if the control session goes silent, a transmit timeout, and an amplifier that defaults to standby when power returns. Switched power with a separate out-of-band path, such as a cellular-linked relay or a second ISP, lets you recover without driving to the site. That also fits the rule that you must be able to shut the station down. Camera and temperature or SWR alerts are cheap compared with a damaged PA or antenna tuner.

On the Icom and Yaesu side, I would treat the LAN port as a trusted-network feature and put a VPN in front of it. Using the radio's own server through a tunnel is generally a safer plan than opening a range of UDP ports, and it keeps CGNAT from being a dealbreaker.

  • Moderators

For latency, measure before you blame the radio. Ping time alone is misleading; look at jitter and loss over a few minutes at the times you actually plan to operate, because Wi-Fi at the client end and a congested home upload are common culprits. Many clients let you tune audio buffer size, and a larger buffer smooths out jitter at the cost of delay. For SSB, a slightly larger buffer is often a better trade than dropouts. For CW, use the keyer-at-the-remote-end approach, since sending timing across the internet is hard to get right.

On the SDR side, the KiwiSDR trick for monitoring your own signal is worth using. If you can hear your transmit audio on a public receiver, you learn what the other end hears, which a local monitor over the same link can't tell you. Just remember it adds its own delay and is not a precise measure of your link. And for the rules, check not only your regulator but also any contest or award you intend to use the station for, because those can be stricter than the licence.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.