Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Getting started with LEO amateur satellites: Doppler handling, tracking software, arrow antennas, and when to move to linear birds

ci_cover.jpg

I'd like to compare notes on the stages of satellite operating, from a handheld and an arrow antenna to a tracked Yagi setup with CAT-controlled Doppler correction. Frequencies, CTCSS tones, and operating status change over time, so check the AMSAT status pages and the current satellite frequency tables before you transmit. Treat anything below as a framework, not a live bulletin.

FM birds (SO-50, AO-91/AO-92 type designs, ISS voice repeater)

FM satellites are the usual entry point because a dual-band HT and a directional antenna are enough. They are single-channel cross-band repeaters, so only one station can use the passband at a time. Keep exchanges short: callsign and grid square (4-character Maidenhead, for example FN31), then clear. Some satellites need a CTCSS tone on the uplink to open the repeater, and SO-50 has historically required an arming tone. Verify the current tone, because a wrong one just gets you silence.

Doppler on FM is easy to underestimate. At 435 MHz the shift across a pass can reach roughly ±10 kHz, and at 145 MHz about a third of that, since shift scales with frequency. On a typical 435 MHz uplink / 145 MHz downlink pair, most of the correction goes on the 435 MHz side. Many operators step the radio's memory or VFO in 5 kHz or 2.5 kHz increments rather than retuning continuously. With a good tracking program, the radio does it for you.

ISS APRS vs. ISS voice repeater

The ISS APRS digipeater is a packet mode, not a voice QSO. It uses the common 145.825 MHz simplex frequency, with 1200 baud AFSK. You can send position beacons or messages, and the main thing to watch is your own path setting. Lengthy or poorly formed paths waste airtime on a shared channel. Voice repeater availability from the ISS depends on crew and station operations, so check before you plan a session around it.

Linear transponders (RS-44, QO-100 narrowband)

Linear birds shift the whole passband, so multiple SSB and CW stations share it simultaneously. That changes the technique. RS-44's transponder is inverting, so when you tune your uplink up, you hear your downlink move down. Many operators pick a downlink frequency first, then adjust the uplink so their returned signal sits on the frequency where they want to be heard. Software that locks the pair together (or CAT that applies Doppler to both VFOs) makes this tolerable. Without it, you will be chasing your own signal. Lower your power as well: a wide linear transponder with strong signals makes everyone's audio worse, and the usual advice is to run the lowest power that gives a readable return.

QO-100 is a different animal. It is a geostationary satellite, so there's no Doppler from the orbit and no pass planning. You get a fixed dish pointing problem instead. A dish in the 60–90 cm class with a suitable feed, a 2.4 GHz uplink, and a 10 GHz downlink through an LNB are typical. The real work is frequency stability: a cheap LNB drifts, and that shows up as the downlink wandering across the passband. Many setups use a stabilised oscillator or software correction against a beacon.

Tracking and control

Gpredict and SatPC32 both take Keplerian elements (TLEs), compute passes for your grid, and can drive your radio via rigctl or CAT. The most common cause of 'it just doesn't track right' is stale TLEs. Update them regularly, especially for low-altitude, drag-affected objects. The second most common is a computer clock that isn't synced. Pass timing errors of a few seconds matter more than most people expect, particularly for rotator control.

Antennas and rotators

An Arrow-style handheld Yagi lets you track by hand: aim by sight and by listening, adjust elevation up and down, and rotate as the bird passes. Circular polarization isn't essential at handheld levels, but polarization fading (QSB) is normal, and rotating the antenna around its boom sometimes helps. Separate the transmit and receive tasks when possible. A common FM setup uses an HT on transmit and a second receiver or a dual-receive radio on the downlink, because you want to hear yourself and the downlink while you are transmitting. Full-duplex capability or a second radio avoids the half-duplex problem where you can't monitor your own signal.

For a fixed station, azimuth/elevation rotators matter most for passes close to zenith. A high-elevation pass requires a very fast azimuth change near the overhead point, which is why some controllers use a 'flip' mode that goes past 180° and tilts elevation beyond 90°. If your rotator can't flip, you will lose signal on overhead passes. Cross-polarized or circular Yagis also help with fading, at the cost of a bit of gain.

Question for everybody: if you were advising someone choosing between a hand-held arrow setup first or a small az/el Yagi system with Doppler control from day one, which sequence would you recommend, and what are the pitfalls in each?

  • Replies 2
  • Views 30
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

If the goal is working stations and not building a station, I'd start with the handheld arrow antenna and an FM bird. The reason is that it teaches pass geometry: where the satellite rises, how its AOS and LOS times relate to elevation, and why a 10-minute window is really about 4 or 5 usable minutes at low elevation. A full tracked system hides some of that, and if something goes wrong you have more variables to separate: the rotator, the software, the CAT interface, the TLE age, the clock.

That said, the arrow route has one painful limit: manual Doppler correction plus pointing plus logging on a single pass is a lot of juggling. If you want to move to RS-44 or other linear birds later, I'd spend the early FM time practicing in Gpredict or SatPC32 without a rig connected. Watch the frequency display, hand-tune against it, and then add CAT control. Once you understand what the software is doing, it's much easier to diagnose when it stops doing it.

One more pitfall for new operators: don't call CQ on an FM satellite as if it were a local repeater. Listen first, give your call and grid briefly, and don't hold the channel. The pass is short, and there may be others waiting.

  • Administrators

I'd lean toward the opposite order if the person already has HF or VHF/UHF SSB experience, because the hardest linear-satellite skill isn't hardware, it's the tuning discipline. On an inverting transponder like RS-44, set a fixed point on the downlink, let the software walk the uplink, and make small manual adjustments with the RIT or the VFO knob. Trying to do it entirely by ear on a handheld is possible, but frustrating for someone who hasn't done it before.

For equipment, a small Yagi pair on a light az/el rotator plus a radio that supports satellite mode and CAT gives a much more forgiving setup than a handheld on a weak SSB signal. Keep an eye on feedline loss on the 435 MHz side, since it hits the receive noise figure, and consider a preamp at the antenna for the downlink if the coax run is long. Remember also that if you transmit on 2 m and receive on 70 cm, you need adequate filtering or physical separation, or the receiver may desense.

A practical tip: before trusting any rotator setup on a real pass, run it against a simulated pass and check that azimuth and elevation limits, the parked position, and the 'overhead flip' behavior all match what the software expects. Errors there tend to show up on the nicest passes, the ones at high elevation.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.