ⓘ Callsign lookups are in real time via the FCC database.
Vanity callsign availability is refreshed daily at 6:00 AM CST.
The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cmvia PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHzDXSpotterInfo
Recent spots—
Select a band above to load spots
Ready — select a band to fetch live spots
Dead rig, no TX, no RX, or protection faults: what order do you check things in?
Most rigs that come in as "dead" or "won't transmit" turn out to be a short list of faults, and the time wasted usually comes from skipping steps rather than from a hard fault. This thread is meant to collect a sensible diagnostic order, plus the test gear and habits that make it quicker. Please argue with any of it.
Start with power, before opening anything. Measure the supply voltage at the rig's DC connector under load, not just at the supply terminals. A supply that reads 13.8 V unloaded can sag badly on transmit because of a tired connector, a corroded fuse holder, thin cable or a weak regulator. Check both fuses on a typical 12 V rig, since one can be open while the other looks fine. Check the reverse-polarity protection too: if someone has connected it backwards, the fuse or a protection diode has probably taken the hit, and other parts may be damaged.
Next, work out whether it is a receive problem, a transmit problem or both. If the display and audio are alive but nothing comes in, check the antenna selection, attenuator, preamp and mode settings. Then try a known-good antenna or signal source. If both TX and RX are dead, suspect a shared path: the antenna relay, the TX/RX switching line, a low supply rail, a bad local oscillator or PLL lock, or a missing reference clock. A frequency counter or scope on the reference oscillator and the PLL lock voltage can tell you a lot within minutes.
For "SWR protection" or "high SWR" faults, always rule out the antenna system first with a dummy load. If the fault clears on the dummy load, the rig is probably fine and the problem is in the coax, a connector, a tuner or the antenna. If it still trips into a good dummy load, look at the forward/reflected detector circuit: the diodes, the balance of the bridge, the trimmers and the op-amp or comparator stage that drives the protection. A shifted detector reading can fold the power back even when the match is actually fine.
On noise, separate noise generated inside the rig from noise coming in from outside. Disconnect the antenna and terminate the input. If the noise stays, check for switching-supply hash, failing electrolytics on the supply rails, a dirty volume pot or band switch, or a poor ground. If it disappears, look at the station: the supply, LED lighting, chargers, and common-mode current on the coax. Ferrites and a different supply are cheap tests.
Blown finals deserve a root-cause hunt, not just a replacement part. Common causes include high SWR, an antenna that was disconnected during transmit, parasitic oscillation, an overvoltage condition, a failed bias circuit, or poor heatsink contact. Replace a failed RF transistor with the correct part, set the bias to the service manual's current with a meter in line, and check the driver stage and the protection circuit before you key up at full power. Use a current-limited bench supply or a dim-bulb limiter so a second failure doesn't take out the next part.
On capacitors, I'd say replace the ones that are suspect, not everything on sight. Bulging, leaking or discolored electrolytics, especially SMD types near warm parts, are obvious candidates. For the rest, an ESR meter or in-circuit checks are more informative than a capacitance reading alone. Mind the polarity and voltage rating, and clean off any electrolyte residue, because it can eat the board traces.
For contact cleaning, use a cleaner that is safe for plastics and for the part in question, and use it sparingly. Switches, potentiometers, relays, plug-in modules and ribbon connectors are all worth reseating or cleaning before you chase a hard fault. Reflow suspicious joints on high-current connectors and at relay pins at the same time.
Alignment comes last, and only against the procedure in the service manual. Slugs and trimmers adjusted without a reference can turn a small fault into a bigger one. Get the manual first if you can: block diagrams, voltage tables, test points and alignment steps will save you more time than any single instrument.
Which instruments do you think give the best return for a hobby bench? A good DMM, a dummy load, a current-limited supply and a scope seem to cover most of it, with a frequency counter, RF probe and signal generator close behind. What would you add or leave out?
Most rigs that come in as "dead" or "won't transmit" turn out to be a short list of faults, and the time wasted usually comes from skipping steps rather than from a hard fault. This thread is meant to collect a sensible diagnostic order, plus the test gear and habits that make it quicker. Please argue with any of it.
Start with power, before opening anything. Measure the supply voltage at the rig's DC connector under load, not just at the supply terminals. A supply that reads 13.8 V unloaded can sag badly on transmit because of a tired connector, a corroded fuse holder, thin cable or a weak regulator. Check both fuses on a typical 12 V rig, since one can be open while the other looks fine. Check the reverse-polarity protection too: if someone has connected it backwards, the fuse or a protection diode has probably taken the hit, and other parts may be damaged.
Next, work out whether it is a receive problem, a transmit problem or both. If the display and audio are alive but nothing comes in, check the antenna selection, attenuator, preamp and mode settings. Then try a known-good antenna or signal source. If both TX and RX are dead, suspect a shared path: the antenna relay, the TX/RX switching line, a low supply rail, a bad local oscillator or PLL lock, or a missing reference clock. A frequency counter or scope on the reference oscillator and the PLL lock voltage can tell you a lot within minutes.
For "SWR protection" or "high SWR" faults, always rule out the antenna system first with a dummy load. If the fault clears on the dummy load, the rig is probably fine and the problem is in the coax, a connector, a tuner or the antenna. If it still trips into a good dummy load, look at the forward/reflected detector circuit: the diodes, the balance of the bridge, the trimmers and the op-amp or comparator stage that drives the protection. A shifted detector reading can fold the power back even when the match is actually fine.
On noise, separate noise generated inside the rig from noise coming in from outside. Disconnect the antenna and terminate the input. If the noise stays, check for switching-supply hash, failing electrolytics on the supply rails, a dirty volume pot or band switch, or a poor ground. If it disappears, look at the station: the supply, LED lighting, chargers, and common-mode current on the coax. Ferrites and a different supply are cheap tests.
Blown finals deserve a root-cause hunt, not just a replacement part. Common causes include high SWR, an antenna that was disconnected during transmit, parasitic oscillation, an overvoltage condition, a failed bias circuit, or poor heatsink contact. Replace a failed RF transistor with the correct part, set the bias to the service manual's current with a meter in line, and check the driver stage and the protection circuit before you key up at full power. Use a current-limited bench supply or a dim-bulb limiter so a second failure doesn't take out the next part.
On capacitors, I'd say replace the ones that are suspect, not everything on sight. Bulging, leaking or discolored electrolytics, especially SMD types near warm parts, are obvious candidates. For the rest, an ESR meter or in-circuit checks are more informative than a capacitance reading alone. Mind the polarity and voltage rating, and clean off any electrolyte residue, because it can eat the board traces.
For contact cleaning, use a cleaner that is safe for plastics and for the part in question, and use it sparingly. Switches, potentiometers, relays, plug-in modules and ribbon connectors are all worth reseating or cleaning before you chase a hard fault. Reflow suspicious joints on high-current connectors and at relay pins at the same time.
Alignment comes last, and only against the procedure in the service manual. Slugs and trimmers adjusted without a reference can turn a small fault into a bigger one. Get the manual first if you can: block diagrams, voltage tables, test points and alignment steps will save you more time than any single instrument.
Which instruments do you think give the best return for a hobby bench? A good DMM, a dummy load, a current-limited supply and a scope seem to cover most of it, with a frequency counter, RF probe and signal generator close behind. What would you add or leave out?
Link to comment
https://www.hamradiobase.com/forums/topic/11407-dead-rig-no-tx-no-rx-or-protection-faults-what-order-do-you-check-things-in/Share on other sites