Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Small lot + HOA: EFHW, doublet, or vertical? Comparing them on efficiency instead of SWR

ci_cover.jpg

Here is a setup that comes up constantly. You have a small suburban lot with maybe 60 to 80 feet of usable run for wire. There is one decent support, such as a tree or a roof-mounted mast, at roughly 25 to 35 ft. The HOA is unfriendly to anything that looks like an antenna. You run 100 W and want to work 40 through 10 m, with 80 m as a bonus.

The usual shortlist is an end-fed half-wave (EFHW), an off-center fed dipole (OCFD), a G5RV, a ladder-line doublet with a tuner, a ground-mounted or elevated-radial vertical, and a small magnetic loop. Every one of them can show a 1.5:1 SWR on some band. That tells you almost nothing about how well it radiates.

Let's compare them on the things that actually decide performance:

1) Height above ground in wavelengths. A 30 ft dipole is about 0.21 wavelength on 40 m and 0.43 wavelength on 20 m, so the takeoff angle changes a lot between bands.

2) Where the feedline and the common-mode current go. An EFHW's coax shield becomes part of the antenna unless you choke it.

3) Loss in the matching system, meaning the transformer, the balun, the tuner and the coax, especially when the feedpoint is far from 50 ohms.

4) Ground loss, which is the big one for verticals.

Which of these do you weight most on a lot like this, and how would you test the answer instead of just trusting the SWR meter?

  • Replies 2
  • Views 29
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

Start with the wire antennas, because on a small lot they are usually the least painful. They all trade something away.

An EFHW is a half-wave wire fed at the end, where the impedance is very high, often a few thousand ohms. That is why the matchbox is a transformer of roughly 49:1 or 64:1. A 40 m version is about 66 ft long and also works on 20, 15 and 10 m as a harmonic. It is easy to hide, because it is one thin wire and a short run of coax. The catch is the return path. With no real counterpoise, current wants to flow on the coax shield, so a good common-mode choke a short distance down the coax matters a lot. Some of the matchbox losses depend on the core material and how hard it is driven. A transformer that looks fine on 40 m can run warm, or lose noticeable power, on a band where the feedpoint impedance is far from the design value. Harmonic operation also means the pattern gets more lobes on the higher bands, and nothing guarantees a low SWR on the WARC bands.

The OCFD is fed at about one-third of the way along, with a 4:1 current balun. The feedpoint impedance is lower than at the end, so the balun's job is easier. It covers 80/40/20/10 m with a reasonable match, and it is usually weaker on 15 and 12 m. The patterns are lopsided on some bands because the legs are unequal. Mechanically you need the full length, around 130 ft for 80 m, and you will not have that on a small lot unless you bend it, and bending costs performance.

The G5RV is a 102 ft flat top fed with a 31 ft ladder-line section, then coax. It is a 3/2-wave on 20 m and needs a tuner elsewhere. It works, but it is not a magic multiband antenna. The coax section after the ladder line sees whatever SWR the tuner is hiding, so you want a choke at the ladder-line-to-coax junction.

My own preference for a one-wire solution that has to cover many bands is a doublet fed with open-wire or window ladder line and a tuner with a balanced output or a good balun. Ladder line is low-loss even at high SWR. It does not care about the 'perfect' match, so the weakness is mostly in the tuner and the balun. Avoid a length that puts a very high impedance (thousands of ohms) on a band you really want, because that stresses the tuner and the balun. It is worth modeling a few lengths in a free modeling program (NEC-based) before cutting wire.

  • Moderators

Agreeing on the doublet, but a few other points on the same shortlist.

On SWR: a bad SWR meter reading at the radio and a good one are both misleading when the coax is lossy. A long run of thin coax can make a terrible antenna look like a 1.3:1 match, because the loss masks the reflection. A quick check is to disconnect the antenna and look at the SWR with the far end open or shorted. A good line should show a very high SWR. If it looks decent, much of your power is going into the cable. For scale, a typical 100 ft run of RG-213 loses roughly 0.6 to 0.7 dB at 14 MHz when matched, and thin RG-58 loses about twice that. Mismatch makes both worse. The takeaway is to keep coax short, use a decent grade, and put the matching point as close to the antenna as practical.

On verticals: a ground-mounted quarter-wave over a poor radial field can look great on the analyzer and radiate poorly. The base impedance over perfect ground is about 36 ohms, but ground loss adds resistance that makes it look closer to 50, so a nice SWR is partly lost power. The fix is radials, either many short ones on or just under the ground, or a small number of elevated radials (often four, each a quarter wave, at a few feet up or higher). Elevated radials are usually easier to live with on a small lot, and sloping them down can pull the feedpoint closer to 50 ohms. A vertical does well for low-angle DX but picks up more local noise than a horizontal wire.

On inverted Vs: an inverted V at a 30 ft apex does something useful on a small lot, since you only need one support and the ends droop. An included angle of 90 to 120 degrees brings the feedpoint impedance down toward 50 ohms, and the resonant length is a bit shorter than a flat dipole. Keep the ends well out of reach, because the high-voltage tips are a safety issue.

On magnetic loops: for a restricted site, a magnetic loop is a real option, indoors or in an attic too, but be honest about the numbers. Efficiency falls steeply on the lower bands for a loop of limited size, and the bandwidth is very narrow, so you retune often. Conductor thickness, the capacitor and the joints decide the losses, and the capacitor voltage can reach the kilovolt range at 100 W. It is a stealthy, quiet-receiving antenna, not a stand-in for a full-size dipole.

A few notes on baluns and ununs. A 1:1 current balun or choke is for suppressing common-mode current, while a 4:1 or 9:1 unit is for transforming impedance. Check the core mix and how many turns or cores are used. Ferrite loss is what makes a choke work, but it also makes it heat up if it is badly chosen or saturated.

For HOA stealth, thin dark wire (dark green or black) against trees works better than most people expect. In the US, the FCC's PRB-1 covers state and local regulations, not private deed covenants, so read your actual documents. It is also not legal advice, so check before you build. For the original question, I would pick the doublet plus choke plus a short coax run, and add a four-radial elevated vertical if the lot allows it. Does anyone have a better trade for 80 m on that lot?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.