Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Getting the most out of 5 watts: rigs, antennas and power for portable QRP

ci_cover.jpg

QRP gets a lot of attention for the gear, but the results mostly come from three things: antenna, band choice and operating technique. This thread is for comparing approaches to low power operation, from the 5 watt CW and SSB basics to kits and portable setups.

First, the numbers. The difference between 5 W and 100 W is about 13 dB, a little over two S-units if you count 6 dB per unit. Plenty of stations can still copy you at that level, especially on CW, where a narrow filter and a trained ear do a lot of work. SSB at 5 W is harder. Voice needs more signal-to-noise ratio than CW, so a good antenna and a quiet location matter more.

QRP-ARCI (the QRP Amateur Radio Club International) is a good reference for how the community defines things. The usual figures are 5 W output on CW and 10 W PEP on SSB. Their contests are a good way to practice, because everyone on the band is working the same way.

Some rigs and kits people compare:

  • Elecraft KX2 and KX3: all-mode, all-band portable radios. The KX2 is smaller and tops out around 10 W. The KX3 is bigger and can go higher with a suitable supply. Check the manual for the input voltage range.
  • Mountain Topper (MTR series): compact CW-only multibander kits aimed at summit activations, with low current draw and a small footprint.
  • Penntek TR-35: a 5 W CW transceiver kit covering several bands, built around being simple and portable.
  • Hendricks QRP Kits: a long-standing source of small kits for building and tinkering. Check the current catalog for what is offered.
  • Pixie-style transceivers: very simple, cheap CW designs. Their selectivity is limited, so they are better as a first build than as a daily driver on a crowded band.

Calling frequencies. These are commonly used QRP gathering spots, and they can differ by region and band plan, so check your local plan before relying on them.

  • CW: 3.560, 7.030, 10.106, 14.060, 18.096, 21.060, 24.906 and 28.060 MHz
  • SSB: roughly 3.985, 7.285, 14.285, 21.385 and 28.385 MHz

These are places to call, not exclusive channels. After a contact, move off the calling frequency to keep it clear.

Antennas and power:

  • Resonant antennas help at low power. A linked or fixed dipole or inverted V in the clear usually outperforms a compromise antenna that needs heavy matching.
  • End-fed half-wave antennas with a 49:1 or 64:1 transformer are popular for portable use. They are light and quick to deploy, though results depend on the counterpoise and feedline.
  • Height and clearance often beat extra wattage. A wire in a tree beats the same wire dragged along the ground.
  • For batteries, 4S LiFePO4 packs are widely used. A fully charged pack sits around 14.4 to 14.6 V, so confirm your radio's maximum input voltage before connecting one. Add an inline fuse regardless of chemistry.

What combinations are you using or considering? Does anyone have strong opinions on a kit versus a ready-made portable rig for a first QRP setup?

  • Replies 2
  • Views 26
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Antenna choice is where most QRP setups succeed or fail. A KX2 into a poorly sited random wire can underperform a simpler rig on a good resonant dipole. If weight and setup time matter, an EFHW with a decent coax run to a tuner-less rig is tough to beat. If you can carry a few extra ounces, a center-fed dipole on a light mast or in a tree tends to be less fussy about the ground and feedline. One tip is to check SWR at the radio each time you change location. A ratio that looked fine at home can drift when the wire is near a tree trunk or a fence.

On power, one caution about LiFePO4: the voltage is flatter than lead-acid, so a simple voltmeter does not tell you much about remaining capacity until the pack drops off. A small coulomb counter or a pack with a built-in indicator helps. Also check the radio's low-voltage cutoff and transmit behaviour before you rely on a pack in the field.

  • Moderators

For kits, it depends on what you want out of it. The Mountain Topper and TR-35 style radios suit people who want a usable CW rig with minimal bulk, and building one teaches a lot about how a small superhet or direct-conversion design is laid out. Pixie-type builds are a different goal. They are great for learning about mixers, keying and audio stages, but expect wide receive bandwidth and drift, so do not judge CW QRP by that experience.

If you are new to CW, I would suggest practicing copy before buying anything. Five watts and a narrow filter will get you contacts, but you still need to hear weak stations through QSB and QRM. Contests with a QRP category, including the QRP-ARCI ones, are a gentle way to build speed because the exchanges are short and predictable. For SSB, plan on a compression-friendly microphone setting and a clear band opening, because there is little headroom to spare.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.