Moving from FM birds to linear: Doppler, tracking software and antennas for SO-50, AO-9x, RS-44 and QO-100
- Replies 2
- Views 29
- Created
- Last Reply
Top Posters In This Topic
-
Mod_Dan 1 post
-
Mod_Chrissy 1 post
This thread is for comparing setups and sorting out what actually matters when you go from working a simple FM pass to running SSB or CW through a linear transponder. The usual path starts with an Arrow-style handheld Yagi and an HT, then branches into SSB/CW on RS-44, APRS or voice repeater contacts via the ISS, and eventually a geostationary bird like QO-100. Each step changes what you need from tracking software, antennas and your own operating habits.
FM satellites (SO-50, AO-91, AO-92 and similar). These are single-channel, cross-band FM repeaters, so only one station can use the transponder at a time. A pass is short, and many stations call at once, so keep exchanges brief: callsign and grid square, then move on. SO-50 has historically needed a specific CTCSS tone to open the repeater, and AO-91 and AO-92 have used their own tones. Satellite status, frequencies and tones change over time and some satellites go quiet, so check the AMSAT status pages and a current frequency list before a pass instead of trusting a bookmark from last year. Most FM operation is full duplex, meaning you hear your own downlink while transmitting. That is the easiest way to confirm you are actually getting into the satellite, and it makes tuning errors obvious.
Doppler shift. The shift is roughly proportional to frequency. A rule of thumb is about 3 kHz either side of nominal on 2 m and about 10 kHz on 70 cm for a typical LEO pass. It starts high on approach, crosses zero at closest approach (TCA), and goes negative as the satellite recedes. On FM you can get by with manual steps on the downlink, such as nudging up a channel step or two at AOS and walking down through the pass. For SSB and CW, small errors make a voice sound like a chipmunk or leave a CW signal wandering, so most people let software do it. Gpredict and SatPC32 can both drive the rig's frequency over CAT. A common arrangement is to let the software correct the downlink and the uplink together so that you tune on the receive side and the transmit side follows.
Linear transponders (RS-44, and QO-100's narrowband section). A linear transponder retransmits a whole slice of spectrum, so many QSOs happen at once, with SSB and CW sharing the passband. RS-44 is an inverting transponder with a 70 cm uplink and a 2 m downlink: as your uplink frequency goes up, the downlink goes down. Its orbit is higher than the typical cubesat, so passes are longer and fade more slowly. That makes it a good place to learn. Look up the current passband edges and beacon frequency before you operate. A useful habit is to first find your own signal in the downlink at low power, then adjust. If you can hear yourself with plenty of margin, you are almost certainly running too much power. Transponder users often ask each other to turn power down, because one strong signal can pull down the gain for everyone else.
ISS: APRS and voice repeater. The ISS has historically carried an APRS digipeater on 145.825 MHz, and the cross-band voice repeater is only active some of the time, depending on the ARISS schedule and crew operations. Check current ISS status before assuming anything is on. APRS contacts are short packets, so Doppler matters less than for voice, but you still need a decent signal into the station. A radio set to 145.825 MHz and an appropriate APRS path is the usual starting point.
Antennas and rotators. A handheld dual-band Yagi, often called an Arrow, is enough for most LEO FM and many linear passes if you can track by hand. Elements are cheap, the boom is light, and you can aim by pointing at the predicted azimuth and elevation as shown by the software. Since the spacecraft antennas are mostly circular or have changing orientation, you will still see fading. Some people use a small crossed Yagi (circular polarization) on a rotator that handles both azimuth and elevation. If you automate with a rotator, remember that overhead passes require fast azimuth moves near TCA, so check the rotator's speed and its cable wrap limits. A flip-over mode, where elevation goes beyond 90° and azimuth turns around, can avoid a rapid swing through the zenith.
Grid squares. Four-character Maidenhead locators (for example, an AB12 style grid) are normally exchanged on satellites, and awards are counted by grid, so keep your own square written down and be ready to give it clearly in phonetics. If you live near a grid line, rovers sometimes operate from a corner point, which lets them activate up to four grids in one trip. Always check your own location in a locator calculator instead of estimating.
QO-100. Because QO-100 is geostationary, there are no passes and no Doppler tracking. The challenge is the hardware: an uplink in the 13 cm band and a downlink at about 10.49 GHz via a dish and LNB. Drift in the LNB's oscillator is the main problem on the receive side, so people use a stable reference or software that tracks the beacon. Coverage footprint matters, so confirm you are within the area the satellite serves before buying a dish.
Questions to get started: what rig and software are you using now for tracking, and are you handling Doppler by hand or over CAT? For linear work, what gives you the most trouble: finding your own signal, keeping a CW tone stable, or antenna pointing?
Link to comment
https://www.hamradiobase.com/forums/topic/11441-moving-from-fm-birds-to-linear-doppler-tracking-software-and-antennas-for-so-50-ao-9x-rs-44-and-qo-100/Share on other sites