Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Getting usable HF from an SDR: direct sampling vs. upconverter vs. a purpose-built receiver, and where the noise really comes from

ci_cover.jpg

This thread is for sorting out a common decision: how to get decent HF reception from an SDR when the cheapest dongle is an RTL-SDR and the better options cost several times as much. The tuner chip in most RTL dongles covers roughly 24 MHz up to the low 1.7 GHz range. HF therefore needs either direct sampling, an upconverter in front of the dongle, or a different receiver altogether.

Here are the usual options and the trade-offs I'd like people to argue about.

Direct sampling on an RTL-SDR. Some dongles, such as the RTL-SDR Blog V3, have a mode that bypasses the tuner and feeds the RTL2832U's ADC directly. It is simple and cheap. The ADC is only 8 bits, though, and there is very little filtering ahead of it. A strong broadcast station at night can fill the converter and produce images and intermod across the band. A bandpass filter or a switchable low-pass filter ahead of the dongle helps a lot more than people expect.

Upconverters. A converter such as a Ham It Up type shifts HF up into the range the tuner can handle. In SDR# you enter the local oscillator frequency as the shift or offset, and HDSDR has an equivalent LO setting. Check the tuning direction. Depending on the mixer injection, the spectrum may be mirrored, and then you need the software's inversion option. The converter's own filtering and gain matter at least as much as the idea of upconversion. Dynamic range is still capped by the 8-bit ADC behind it.

Purpose-built receivers. The SDRplay RSP family has an internal front end with filtering and more ADC resolution, and is mainly used with SDRuno on Windows. The Airspy HF+ line is designed for HF and VHF with an emphasis on strong-signal handling. A HackRF covers a huge frequency range, but its 8-bit converter and general-purpose design make it a poor first choice for serious HF listening. A LimeSDR is a flexible transceiver for experimenters. It is overkill for casual shortwave listening, and it needs more setup.

Software side. SDR#, SDRuno, HDSDR, GQRX and CubicSDR all do the same core job of showing a waterfall and demodulating. Each fits a different environment. SDRuno works with SDRplay hardware. HDSDR uses ExtIO drivers and can follow a transceiver over CAT, which suits panadapter use. GQRX is the usual choice on Linux and runs on top of the gr-osmosdr or SoapySDR stack. CubicSDR is cross-platform and goes through SoapySDR. The software matters less than the front end, but features like notch filters, noise blankers and a good bandscope decide how pleasant a receiver is to use.

Noise. A lot of HF noise is local interference rather than the receiver. Switch-mode power supplies, LED lighting, USB hubs and the PC itself can lift the noise floor by many dB. Use a USB extension cable with a ferrite choke, put the dongle away from the computer, and consider a common-mode choke on the coax. Antennas matter too. A short whip indoors will mostly pick up household noise. An outdoor wire, loop or active antenna away from the house usually improves the signal-to-noise ratio more than a better receiver would.

Questions for the thread: at what point is a filter ahead of an 8-bit dongle worth more than a new receiver? Is a panadapter from a transceiver's IF output a better use of money than a standalone SDR? And how do you tell overload from genuine band activity on a waterfall?

  • Replies 2
  • Views 31
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

For overload versus real signals, the quick test is to change the gain and see what moves. Drop the RF gain or add attenuation. Real signals will fall by roughly the same number of dB and their relationship to the noise floor stays similar. Images and intermod products usually move by a different amount, or vanish quickly. If a ghost signal appears that doesn't match a known band plan, also check whether it still appears when you disconnect the antenna. If it stays, it's internal, and USB noise or a poor power supply is a suspect.

On filtering ahead of an 8-bit dongle, I'd say it can be worth more than a hardware upgrade if you live near strong broadcast transmitters. A bandpass for the band you want, or a broadcast-band notch for FM, cuts the total power reaching the ADC. That matters more than the nominal noise figure, because the limit is the strongest signal rather than the weakest one. If you are in a quiet location, the difference may be smaller.

  • Moderators

On the panadapter question, the two approaches solve different problems. A standalone SDR gives you a whole receiver. A panadapter taps the transceiver's IF and uses the SDR for the display only, so audio quality, filtering and AGC stay with the radio. The common pitfalls are the IF level and frequency alignment. The tap needs to be properly buffered so you don't load the radio's receive path, and the SDR software needs the right offset to show true frequency. Without CAT or a similar link, the waterfall will drift from what the radio is tuned to.

For digital modes the signal path is mostly the same regardless of the receiver. Demodulate in SDR software, then pass audio to the decoder through a virtual audio cable or a loopback device. WSJT-X handles FT8 and similar modes. fldigi covers many older modes. Satellite and data decoders like SatDump or rtl_433 often work from IQ directly. Watch the sample rate and the audio level, since an over-driven soundcard path is a more common cause of failed decodes than the SDR itself. Clock accuracy also matters for narrow modes, so a TCXO or a calibrated PPM offset is worth setting up.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.