Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dual-band mobile radio planning: FTM-500D vs ID-5100A vs TM-D710G, plus wiring, noise and cross-band basics

ci_cover.jpg

Picking a 2 meter / 70 centimeter mobile usually comes down to which ecosystem you want, because all three of these radios are 50 W-class dual-banders. The Yaesu FTM-500D is built around C4FM digital with analog FM. The Icom ID-5100A is a D-STAR radio with a touchscreen head and analog FM. The Kenwood TM-D710G is an analog FM radio with built-in APRS (TNC and GPS), and it is often chosen by people who want position reporting and messaging without extra boxes. Check which digital modes are active on the repeaters you actually use before buying. A radio that can't talk to your local network is a lot less useful, however nice its display is.

Whichever radio you choose, the installation matters as much as the model. A few points are worth settling before you drill anything:

Power wiring. A 50 W FM radio can pull roughly 10 to 12 A or more on high-power transmit, so skip the cigarette-lighter socket. Those circuits are shared, thinly wired and add voltage drop. Run the supplied power cable to the battery, with the fuse holder on the positive lead as close to the battery terminal as practical. That fuse protects the cable run, so a fuse only at the radio end leaves the long section unprotected. Use the fuse rating the manufacturer specifies. If you have to extend the cable, use heavier wire than the stock gauge, and make good crimped or soldered joints rather than twisted ones. Use a grommet wherever the cable passes through sheet metal. Some newer vehicles have a battery monitoring sensor on the negative terminal, so check the service information before choosing a ground point.

Mounting. Keep the radio body and control head away from airbag deployment zones and anywhere a loose unit could become a projectile. Leave room around the heatsink and fan. Mount the microphone hanger where you can reach it without looking. If the radio supports a separated head, as the ID-5100A and FTM-500D do, plan the cable route and where the body will live. Don't coil excess coax or cable into a tight bundle beside the radio.

Antenna and feedline. A well-grounded roof-center antenna usually works better than a trunk-lip or magnet mount. At 440 MHz, cheap thin coax loses more than at 146 MHz, so don't skimp on the feedline. Check SWR on both bands, not just one.

Noise. Alternator whine, ignition noise and hash from LED lighting, USB chargers or DC-DC converters can show up as a squelch that won't close, or as whine on your transmitted audio. Keep the power lead away from the vehicle harness, separate it from the coax, and test by switching accessories on and off while listening on a weak signal. Ferrite chokes can help in some cases, but a poor ground or a noisy accessory should be fixed at the source.

For discussion: how do you weigh the digital ecosystem against the features you'd use daily, such as APRS, cross-band repeat and a readable display? And what is your approach to power and ground routing in a newer vehicle?

  • Replies 2
  • Views 29
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Cross-band repeat is worth thinking through before you rely on it. The radio receives on one band and retransmits on the other. A typical use is a handheld on UHF reaching the mobile, which repeats on VHF through the vehicle's better antenna. Whether it's a good fit depends on the radio's menu options and your local rules. Your station still needs proper identification, and you are the control operator. Never set it up on or near a repeater's input or output frequency. Choose frequencies where you aren't interfering with anyone, and consider adding a CTCSS tone so stray signals don't trigger the system.

Remember that transmitting continuously generates heat. Using a lower power setting is often enough, and it is easier on the finals. Read the manual for your specific model, because the way cross-band is configured, and whether you can use it with digital modes, varies between Yaesu, Icom and Kenwood. The TM-D710G is commonly associated with a cross-band function, but verify the exact menu steps in its manual instead of assuming it works like another brand's.

Also test with the vehicle parked and the engine running. Some noise problems and RF feedback into a handheld only appear under real conditions.

  • Moderators

On etiquette, the main rule is that driving comes first. Use a steering-wheel PTT or keep calls short and simple, and don't try to operate a menu-heavy screen on the move. Check your local laws on hand-held microphones, since those vary. If you're not in a position to talk safely, just listen.

On the air, listen before you key up. Give your call sign clearly, and keep calls and QSOs short, especially on busy repeaters. If you're only passing through, a brief call is enough. Don't monopolize a repeater with a long conversation when simplex is an option. In the US, 146.52 MHz and 446.000 MHz are the common simplex calling frequencies, but check your local band plan. Before transmitting on a digital radio, check which mode the radio is in. Auto mode-select features, like AMS on Yaesu radios, can be convenient but can also surprise you, and D-STAR users should confirm their routing and reflector settings so they don't transmit unintended traffic.

Finally, treat noise as an etiquette issue too. If your installation has a noisy alternator or accessory, your transmitted audio can be harder to copy for everyone, and a clean install is a courtesy to your listeners as well as a convenience for you.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.