Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dead rig triage: what do you check first when there is no TX and no RX?

ci_cover.jpg

I'd like to put together a sensible order of operations for a rig that shows nothing useful on either transmit or receive. The aim is to avoid the habit of grabbing a soldering iron before you know which block is at fault. It should cover HF transceivers, VHF/UHF mobiles and older tube-and-transistor gear, with the specifics adjusted per model.

Here is my starting skeleton. First, confirm what the rig really sees as power: supply voltage at the rig's DC connector while it is running, and the fuse in both legs of the cable. Second, find out whether it is truly dead or only partly dead. Does the display come up? Is there any audio noise or squelch tail? Does the PTT make the relay click or the meter move? Third, split the problem into power, control/synthesizer, receive path and transmit path, and check the shared parts first, since a fault there would explain both symptoms at once.

Where I'm less sure is how much to trust on-board protection. If a rig folds back power or refuses to key, how do you separate a real fault (high SWR, overtemperature, overcurrent) from a false trip caused by a failed sensor or a dirty connector? And at what point do you stop poking around and pull the service manual for the alignment and voltage tables? Corrections and additions welcome, especially anything that saves someone from killing a good final by testing carelessly.

  • Replies 2
  • Views 28
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Your skeleton is close to how I'd order it. I'd put the shared-resource check even earlier. When both TX and RX are dead, the usual culprits are DC input, a regulator rail, or the PLL/reference oscillator. Measure at the rig, under load if you can, because a supply that reads 13.8 V open-circuit can sag badly through a corroded fuse holder or a worn Anderson/Powerpole contact. A voltage drop measured across the connector or fuse holder while the rig is drawing current finds this quickly. If there's a current-limited bench supply, watch what the rig draws at power-up. Almost no current, or a hard limit, tells you a lot before you open the case.

After that, open the manual's block diagram and look for the common rails: 5 V, 8 V, 9 V and so on. Check each at the regulator output and at the far end of its run, since a regulator that is fine at the pin can still be pulled down by a shorted bypass cap downstream. A failed ceramic or tantalum cap on a rail is a classic dead-board cause, and a warm part on a current-limited supply will often point to it. The PLL is the other shared item: if the VCO doesn't lock, many rigs mute RX and inhibit TX together. The manual usually names a lock-detect voltage, so you can test it with a multimeter before reaching for a scope.

For receive-only dead, I like working backwards from audio. Inject a tone at the volume control or the AF amp input, then work toward the antenna with a signal generator at IF and then RF. Before assuming a bad IC, check the speaker jack and headphone-switch contacts. A contact cleaner suited to switches and pots, applied sparingly and kept off plastics, solves more of these than it should.

  • Moderators

On the protection question, the first rule is to test into a dummy load, never an antenna, and use a wattmeter you trust. If the rig folds back or flags high SWR into a known-good dummy load, the fault is inside. The usual suspects are the directional coupler or bridge, a failed detector diode, a drifted trimmer, a bad solder joint, or an RF-sensing line that has lost its reference. Compare forward and reflected detector DC voltages against the manual. A reflected reading that is high on a dummy load usually means the sensor, not the antenna system. The other possibility is a mismatch inside the rig, such as a damaged output filter or relay contact, so don't assume the final is healthy just because it isn't smoking.

If a final has already failed, work out why before replacing it. Common causes are high SWR, an unstable driver or parasitic oscillation, an overvoltage supply, bias runaway, and a wrecked protection circuit. Check the bias network, thermistor or diode, emitter resistors, and driver stage too. Replace with the correct part, and where the design calls for a matched pair, treat that seriously. Set idle current to the manual's figure, with the supply current-limited and a dummy load connected, and bring power up in steps. Be wary of suspiciously cheap RF transistors, because bad parts are a real problem in this market.

On capacitors: replace what you can show is bad, or what is known to be a problem on that model, rather than recapping on a hunch. An ESR meter and a visual inspection for bulging, leakage and corrosion get you most of the way. Leaked electrolyte from SMD caps eats traces, so clean it with isopropyl and a brush and check continuity afterwards. For switching supplies, use low-ESR, adequately rated parts. For noise, first terminate the antenna port with a dummy load. If the noise stays, it's internal or from the supply, and running the rig from a battery is a quick test for a noisy switcher. If it goes away, look at the antenna, feedline and the household around you. A scope helps here, but use a 10x probe with a short ground spring, and never clip a grounded scope onto a circuit connected to a non-isolated supply.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.