Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a homebrew QRP station from scratch: build order, test gear, and where each project teaches you something

ci_cover.jpg

Homebrew radio covers a lot, from a crystal set with no power source to a multiband SSB rig built around a DDS or Si5351 synthesizer. That range makes it hard to decide what to build first. This thread is for comparing build orders and sharing the practical details that kit instructions often skip.

Here is one possible progression to argue about. Start with a crystal radio or a simple direct conversion receiver to learn tuned circuits, detection, and audio gain. Move to a crystal-controlled CW transmitter such as a Tuna Tin 2 style oscillator/PA or a Pixie-type transceiver, which shows what an RF stage does in practice. Then build the accessories that make a station usable: low-pass filter, SWR bridge, keyer, and a clean power supply. After that, try a BITX or uBITX-class transceiver, where you are working with mixers, filters, VFO or synthesizer control, and bidirectional amplifier stages.

Some questions to get started. Which of these steps teaches the most per dollar? Should an SWR bridge and dummy load come before the first transmitter? And what is the minimum test equipment that lets you tell a working circuit from one that only seems to work: a multimeter, a dummy load, an RF probe, a frequency counter, a NanoVNA, or an oscilloscope?

Please include numbers where you can, such as supply voltage, output power, filter type and component values, and measured versus expected results. Vague reports like 'it works' are hard for the next builder to learn from.

  • Replies 2
  • Views 28
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd keep the order roughly as proposed, with one change: build the dummy load and a basic RF probe before the first transmitter. A 50 ohm load made from several non-inductive resistors in parallel is cheap. Without it, early tests end up on an antenna, which confuses everything. You can't tell whether a poor result comes from the circuit or from the antenna, and you may be radiating something you haven't checked.

The Pixie family is worth building mostly for what it demonstrates. In the usual versions, one transistor oscillator serves as the transmitter and also as a detector on receive, followed by an audio amplifier such as an LM386. It is not a good receiver. There is almost no selectivity, and strong out-of-band signals get through. But it shows how crystal-controlled keying works and how little a simple CW transmitter needs. The Tuna Tin 2 is the better lesson on transmitter basics. It is a crystal oscillator with a power stage, and it makes you think about the output network, supply decoupling, and why the key line should have some shaping. Without shaping you get key clicks that spread across the band. Output on these simple designs is typically in the low hundreds of milliwatts, so the stage-by-stage voltages are easy to check with a multimeter and a probe.

For direct conversion receivers, the usual problems are worth knowing before you build. You hear both sidebands, because there is no sideband rejection unless you add a phasing network. Strong AM broadcast stations can break through if the front end has no filtering. Audio-stage hum and microphonics show up, especially with high gain after the mixer. A bandpass filter at the input and a sensible audio low-pass go a long way. A diode ring mixer or an NE602/SA612-style mixer is a reasonable choice. Use an LNA only if you can handle the extra overload risk.

On soldering: use a temperature-controlled iron with a clean tip, use flux freely, and clean the board afterward when you can. Many 'dead' kits turn out to have cold joints, solder bridges between pads, or an electrolytic installed backwards. Inspect every joint before you power anything up.

  • Moderators

On test gear, I'd split it into three tiers. The first is a multimeter, a dummy load, an RF probe or diode detector, and a bench supply with current limiting. That is enough to verify DC bias and see whether RF exists. The second tier adds a frequency counter or an SDR receiver for watching your own signal, a NanoVNA for filter and SWR work, and an oscilloscope. The third tier is a spectrum analyzer or equivalent, which is the only real way to see harmonics and spurs.

Harmonics matter most once you move to BITX or uBITX-class designs, where the final amplifier uses MOSFETs or similar devices that produce significant harmonic content. The low-pass filters in these radios are often per-band, and a filter that is mistuned, has the wrong inductors, or is switched incorrectly can leave harmonics unsuppressed. Check your local regulations for the limits that apply to you. If you use an SDR to look at your output, put a large attenuator between the rig and the receiver. Connecting transmitter output directly to an SDR input can damage it.

For the SWR bridge, the common choices are a Tandem Match or Bruene-style directional coupler. The key check is the null: terminate it in a good dummy load and adjust the balance trimmer until reflected reading is as low as you can get it. Then reverse the connections or compare against a known-good instrument. Even a home-built bridge is useful for relative adjustment of an antenna tuner, but don't trust the absolute numbers until you've verified them against a known load.

For power supplies, supply noise is a real problem in sensitive receivers. A linear regulator with proper bypassing is easier to get quiet than a cheap switching supply, which can put hash across the HF bands. If you do use a switcher, test the receiver with the supply running and the antenna disconnected, then with a battery for comparison. For keyers, an iambic keyer built around a microcontroller is easy to make. Isolate the keyed line with a transistor or optocoupler and add an RC time constant to soften the edges, so the keyer doesn't generate its own click problem.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.