Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Small lot or HOA: EFHW, doublet, inverted V, vertical or loop? What trade-offs actually matter

ci_cover.jpg

Let's work through the standard small-lot, HOA-sensitive problem: roughly 60 to 70 feet of usable horizontal run, one or two supports around 25 to 35 feet, no towers, nothing that looks like an antenna from the street, and a wish to cover 80 through 10 meters. Every option below makes a different compromise, and the compromises are often hidden behind a low SWR reading.

An end-fed half-wave (EFHW) is popular because it is easy to deploy. A 40 m version is about 66 ft of wire, fed through a transformer of roughly 49:1 or 64:1 to bring a feedpoint impedance of a few thousand ohms down to something near 50 ohms. A 40 m EFHW is resonant on its harmonics, so it is usable on 40, 20, 15 and 10 m. It is not naturally resonant on 30, 17 or 12 m, and those bands need a tuner and have an unpredictable feedpoint. The weak point is the counterpoise. With no radials, the coax shield becomes part of the antenna, so a common-mode choke at the feedpoint end of the coax is worth having.

An off-center fed dipole (OCFD, or Windom type) feeds the wire about a third of the way along, usually through a 4:1 current balun. It covers a similar set of bands to the EFHW, with a lower feedpoint impedance and less reliance on the coax as a counterpoise. Its patterns on the higher bands are lumpier than a plain dipole, and on some bands the SWR is acceptable but not great.

A G5RV is a roughly 102 ft doublet with a 31 ft section of 300 or 450 ohm line, designed around the 20 m band. It is a decent compromise if you plan to run a tuner anyway, but it is not a no-tuner multiband antenna. A general doublet with ladder line and a tuner is often a better choice because you can tailor the length and the feed line to your layout and avoid the lengths that lead to extremely high impedance on a band you care about.

So what would you put up first, and why?

  • Replies 2
  • Views 31
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

For a first multiband install in tight space, I'd put the focus on three things: where the current is flowing, how high the radiating part of the wire is, and how much loss is in the matching system. A flat SWR does not tell you any of these.

On height: a horizontal dipole's pattern depends heavily on its height in wavelengths. At 30 ft, 40 m is only around 0.2 wavelength high, so a lot of the energy goes up at high angles. That works well for regional contacts, but it is less impressive for DX. The same 30 ft is about 0.43 wavelength on 20 m, which gives a much better takeoff angle. An inverted V with the apex at the best height you can manage is a perfectly reasonable compromise. Droop the ends and the resonant length shrinks a bit, so trim by measurement and not by the formula alone. Also keep the ends out of reach, because the voltage there can be high enough to burn someone touching them.

For stealth, the wire itself is the easy part. Thin insulated wire, tied off at trees or eaves, is hard to spot. It is the feed line and the tuner or transformer that people usually notice. If you are using a doublet with ladder line, you can keep a lot of the feed line away from the house, but the line should not run parallel to metal gutters, and the routing needs some thought.

Verticals are a different trade. A ground-mounted quarter-wave over only a handful of short radials will lose a significant share of the power in ground resistance. Elevated resonant radials, typically 2 to 4 per band, are more efficient per radial than a ground-laid system with few radials. If you can lay down a large number of radials, either approach can work, but for a small lot the vertical typically works better for low-angle DX and worse for noise, since it picks up more local man-made noise than a horizontal wire.

  • Administrators

One point on SWR and coax loss that's worth separating out. SWR at the rig tells you only how well the transmitter sees the system, and a dummy load would show 1:1. What matters is how much power reaches the radiator and how much is lost on the way. Matched-line loss for common coax rises with frequency, and with high SWR the loss increases beyond that figure. That is why ladder line plus a tuner can beat coax on a band where the antenna is far from resonance: the line itself has low loss even at high SWR. The loss often occurs elsewhere in the chain, in the tuner, the balun or a choke that has saturated or is being driven at a mismatched impedance.

Balun versus unun terminology also trips people up. A 4:1 balun on a doublet or OCFD is there to convert unbalanced to balanced and to match impedance. A 49:1 unun on an EFHW is mostly a transformer. Either way, the coax outside can carry common-mode current, which is why a choke of sufficient impedance is a common fix. If changing the coax length or touching the cable changes your SWR reading, that suggests the shield is part of the radiating system.

Finally, on magnetic loops: a small loop can be a good fit for an attic or balcony, and it often has a lower receive noise level than a wire. It also has very narrow bandwidth, so you retune it whenever you move more than a few kHz. Its efficiency depends strongly on loop size and on resistive loss in the conductor and the joints, and the capacitor voltages can be high at power. It is a legitimate tool for a restricted site, but not the first thing to choose unless the HOA problem leaves no wire option.

A practical way to compare candidates: use an antenna analyzer to find the resonances, check the effect of a choke on a given feed line, and then compare receive signal-to-noise on real signals. Modeling software such as NEC-based programs is useful for seeing how height and ground change the pattern before you put anything up.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.