ⓘ Callsign lookups are in real time via the FCC database.
Vanity callsign availability is refreshed daily at 6:00 AM CST.
The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cmvia PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHzDXSpotterInfo
Recent spots—
Select a band above to load spots
Ready — select a band to fetch live spots
Building an HF shack around a 100 W rig: what matters more than the radio badge?
Rig comparisons usually go IC-7300 vs FT-991A vs TS-590SG, and the rest of the station gets treated as an afterthought. In practice the antenna system, power, grounding, and RF management often decide how a station performs more than the front panel does. I'd like this thread to cover the whole chain, not just the transceiver.
Here is a rough framework to argue with.
1. Pick the rig for the operating style, not the spec sheet. The IC-7300 is a single-receiver direct-sampling 100 W rig with a built-in tuner. The IC-7610 adds a second receiver and separate RX antenna handling, which helps for contesting or chasing DX with a split pile-up. The FT-991A covers HF through UHF in one box, and the FTDX10 is HF/6 m only with a more HF-focused receiver design. The TS-590SG and TS-890S are Kenwood's superhet approach with roofing filters. The K3S is a modular, highly configurable 100 W platform, and the KX3 is a compact QRP rig that also works as a home station with an outboard amp. The Xiegu G90 is a 20 W portable-oriented SDR with a built-in tuner, so it is a different class of radio from the 100 W desktop rigs. Which of these suits you depends on whether you need dual receive, an HF/VHF/UHF all-in-one, portability, or the best behavior in crowded band conditions.
2. Power supply. A 100 W rig at 13.8 V can pull roughly 20 A or more on SSB peaks, so a 25-30 A supply is a common choice for headroom. Switching supplies are small and efficient, but some radiate noise into HF receivers. Check the band noise with the supply on and off, and be ready to add ferrites or move it away from the receive antenna feedline. Use properly sized cable, fuse the positive lead near the source, and standardize on connectors you trust.
3. Tuner and amplifier placement. An ATU makes your transmitter see a friendly load, but it does not make a poor antenna efficient. If the mismatch is at the antenna end of a long coax run, the feedline loss is still there. If you add a linear, set the drive level correctly, wire the ALC and keying, and put the tuner after the amplifier if you need it for the antenna. Then check for splatter on a second receiver or SDR.
4. Band-pass filters. They matter most when you have another transmitter nearby, as in multi-op or SO2R, or when a nearby broadcast or ham signal overloads the front end. For a single-operator station with no local interference, they are often unnecessary, and they add insertion loss and another failure point.
5. Grounding and bonding. Keep three things separate in your head: AC safety grounding, lightning protection, and RF management. Bond station equipment together, bond any outdoor ground system to the home's electrical grounding electrode system, and check local code for specifics. A ground rod alone will not fix RF in the shack. Common-mode chokes on the feedline and on USB/audio cables are often more effective.
Where would you spend the first extra dollar: a better antenna, RX antenna, power supply, filters, or a rig upgrade? And what would you change in the order above?
Rig comparisons usually go IC-7300 vs FT-991A vs TS-590SG, and the rest of the station gets treated as an afterthought. In practice the antenna system, power, grounding, and RF management often decide how a station performs more than the front panel does. I'd like this thread to cover the whole chain, not just the transceiver.
Here is a rough framework to argue with.
1. Pick the rig for the operating style, not the spec sheet. The IC-7300 is a single-receiver direct-sampling 100 W rig with a built-in tuner. The IC-7610 adds a second receiver and separate RX antenna handling, which helps for contesting or chasing DX with a split pile-up. The FT-991A covers HF through UHF in one box, and the FTDX10 is HF/6 m only with a more HF-focused receiver design. The TS-590SG and TS-890S are Kenwood's superhet approach with roofing filters. The K3S is a modular, highly configurable 100 W platform, and the KX3 is a compact QRP rig that also works as a home station with an outboard amp. The Xiegu G90 is a 20 W portable-oriented SDR with a built-in tuner, so it is a different class of radio from the 100 W desktop rigs. Which of these suits you depends on whether you need dual receive, an HF/VHF/UHF all-in-one, portability, or the best behavior in crowded band conditions.
2. Power supply. A 100 W rig at 13.8 V can pull roughly 20 A or more on SSB peaks, so a 25-30 A supply is a common choice for headroom. Switching supplies are small and efficient, but some radiate noise into HF receivers. Check the band noise with the supply on and off, and be ready to add ferrites or move it away from the receive antenna feedline. Use properly sized cable, fuse the positive lead near the source, and standardize on connectors you trust.
3. Tuner and amplifier placement. An ATU makes your transmitter see a friendly load, but it does not make a poor antenna efficient. If the mismatch is at the antenna end of a long coax run, the feedline loss is still there. If you add a linear, set the drive level correctly, wire the ALC and keying, and put the tuner after the amplifier if you need it for the antenna. Then check for splatter on a second receiver or SDR.
4. Band-pass filters. They matter most when you have another transmitter nearby, as in multi-op or SO2R, or when a nearby broadcast or ham signal overloads the front end. For a single-operator station with no local interference, they are often unnecessary, and they add insertion loss and another failure point.
5. Grounding and bonding. Keep three things separate in your head: AC safety grounding, lightning protection, and RF management. Bond station equipment together, bond any outdoor ground system to the home's electrical grounding electrode system, and check local code for specifics. A ground rod alone will not fix RF in the shack. Common-mode chokes on the feedline and on USB/audio cables are often more effective.
Where would you spend the first extra dollar: a better antenna, RX antenna, power supply, filters, or a rig upgrade? And what would you change in the order above?
Link to comment
https://www.hamradiobase.com/forums/topic/11535-building-an-hf-shack-around-a-100-w-rig-what-matters-more-than-the-radio-badge/Share on other sites