Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

VHF/UHF antenna choices: J-pole, slim jim, 5/8 wave, collinear, yagi, and what matters more than the antenna type

ci_cover.jpg

This thread is for comparing common VHF/UHF antenna designs and the installation details that often decide whether they work. The starting question is simple: you want to work local repeaters, simplex, and maybe a satellite pass. Which antenna do you build or buy, and where do you put it?

Quarter-wave whip: about 19 inches on 2 m and about 6.5 inches on 70 cm. It is mechanically simple and has roughly unity gain over a ground plane, so the ground plane is part of the antenna. On a car, the roof is that ground plane. A mag mount on the center of a steel roof behaves very differently from the same whip on a trunk lip or a fiberglass panel.

5/8 wave: the usual step up for mobile and some base antennas. A matching coil at the base cancels the reactance, and the pattern is pushed lower toward the horizon. Ideal gain is about 3 dB over a quarter-wave, but real-world numbers depend heavily on the ground plane and the matching. Dual-band mobile whips often use a 5/8 wave on 2 m and a stacked 5/8 arrangement on 70 cm. The gain ratings are marketing numbers unless the pattern was measured on a proper ground plane.

J-pole and slim jim: both are end-fed half-wave antennas with a quarter-wave matching section. The slim jim is a folded variant of the same idea. Gain is about that of a half-wave dipole, so don't expect more just because it is tall. They are cheap, rugged, and need no radials, but the feedline can still carry common-mode current and distort the pattern. A choke of several turns of coax or a few ferrites at the feedpoint helps, and mounting the antenna away from the mast also helps.

Collinear: stacked half-wave sections phased to narrow the vertical beam. Typical commercial base antennas run from about 6 to 9 dBd. The extra gain comes from squeezing the pattern toward the horizon, so a collinear on a hill or tower is excellent, while one in a valley or near a house may overshoot nearby stations. Mount it high, above surrounding metal, and keep the mast clear of the radiating sections.

Yagi: this is the directional option. Gain depends on boom length, roughly 6 dBd for a few elements and 10 or more for long booms. Use vertical polarization for FM repeaters and simplex, and horizontal for SSB and CW weak-signal work. A rotator is nice, but for a fixed repeater path a fixed yagi aimed at the machine can beat any omni.

Feedline matters as much as the antenna. Loss rises quickly with frequency. As rough numbers, RG-58 is around 4 to 5 dB per 100 ft at 150 MHz and around twice that at 450 MHz. LMR-400-class cable is around 1.5 dB per 100 ft at 150 MHz and 2.7 dB at 450 MHz. Check the datasheet for the exact cable. A 6 dB-gain antenna on a long run of RG-58 can end up worse than a plain dipole on short low-loss coax.

Connectors: the PL-259 (UHF connector) is fine on 2 m at modest power, but it is not constant impedance and is poor on 70 cm and up. An N-type is constant impedance, weatherproof with its gasket, and a better choice for outdoor 440 MHz work. For the car, NMO is the standard for a permanent mount. It needs a 3/4 inch hole and a good ground at the mount, but it is much more reliable than a mag mount for long-term use. Whatever you use, waterproof outdoor connectors with self-amalgamating tape and add a drip loop in the cable.

SWR tells you how well the antenna is matched to the feedline. It does not tell you how well the antenna radiates. A dummy load shows 1:1 and radiates nothing. Measure at the antenna end if you can, because long lossy coax can make a bad antenna look better than it is. Check across the band, not just on one frequency.

Polarization: the mismatch between a vertical and a horizontal antenna on a direct path can be 20 dB or more in theory and typically 10 to 20 dB in practice. Reflections may help or hurt. For satellites, the polarization rotates with Doppler and spacecraft tumbling, so circularly polarized antennas, such as crossed yagis, avoid deep fades. Many people work FM satellites with a handheld Yagi and accept some polarization fading.

What have you found works for your situation, and what do you want to compare: gain versus pattern, cable versus connector, or a build versus buying?

  • Replies 2
  • Views 30
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One caution on the J-pole and slim jim. They are often described as ground-plane-free, which is true for the matching, but the pattern can still be skewed if the feedline radiates. If the coax comes off horizontally for several feet and the antenna is mounted on a metal mast, the pattern and SWR can change. Keep the bottom of the antenna clear of the mast by a decent distance, run the coax away at a right angle, and use a choke at the feedpoint. Also, those "3 dB" figures on an antenna tag are usually the maximum in an idealized case. If the main goal is a repeater a long way off, take-off angle and height matter more than the label.

On mobile, a 5/8 wave on the center of a steel roof is a very hard combination to beat. If you have a vehicle with a fiberglass or aluminum roof, results can be quite different, and a quarter-wave may behave better than a 5/8 over a poor ground.

  • Moderators

For the coax-and-connector question, consider the whole run before choosing. If you have a short run of 15 to 20 ft on 2 m, RG-8X or similar is usually fine. If it is 70 cm or longer, go to a low-loss type with N connectors. PL-259s are easy to get wrong: a cold solder joint, or a shield that is not tight at the back of the connector, gives intermittent noise and SWR problems, and they also let water in unless sealed. Use the correct reducer for the cable diameter.

For satellites, a small hand-held yagi like an Arrow-style, or a pair of crossed yagis on an az/el setup, is the usual pair of options. A fixed omni, such as a turnstile or a quadrifilar helix, is a quieter choice if you want to avoid a rotator and are OK with lower gain. For a repeater, the question is different. The Tx and Rx need isolation, so the choice is either a duplexer, with a single antenna, or two antennas separated vertically with a good gap, which is cheaper than cavities but needs a tower.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.