Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

50 ft lot, HOA, 100 W: EFHW, OCFD, or ladder-line doublet for 80–10 m?

ci_cover.jpg

Here is a common scenario that should give us something concrete to compare. The lot is about 50 ft wide and 100 ft deep. There is one tall tree at the back, a roofline at roughly 20 ft, and a 100 W rig. The HOA bans visible towers, beams and anything that looks like an antenna. Wire is probably tolerated if it is hard to see. The operator wants 40 m through 10 m, would like 80 m or 60 m if possible, and mostly wants DX plus the occasional regional net.

The candidates are an end-fed half-wave (EFHW) with a 49:1 or 64:1 transformer, an off-center fed dipole (OCFD), and a doublet fed with ladder line into a tuner. A G5RV and a vertical on a pole could also be options. Rather than argue which is best, it may be more useful to compare what each one costs in efficiency, in noise pickup and in hassle.

Some points I would like to see discussed:

1. Height matters more than the antenna name. A horizontal wire 20 ft up on 40 m is only about 0.15 wavelength high. It will favor high-angle radiation, which is good for 300–800 mile contacts and weaker for DX. The same wire is a more reasonable DX antenna on 15 and 10 m, where 20 ft is a larger fraction of a wavelength.

2. An EFHW is attractive because it is one wire and one feed point at the end. But the transformer is not the whole antenna. The coax shield often becomes the counterpoise, so a choke at the feed point and some thought about where the coax runs are important. A low SWR on every band does not prove the antenna is efficient. It only shows that the load looks like roughly 50 ohms.

3. For the doublet, ladder line has very low loss even with a high SWR. The tuner and the coax between radio and tuner are where the loss accumulates. Where does the tuner sit, and is a common-mode choke used at the entry point?

So for this lot, what would you put up first, and what would you measure to decide whether it is working?

  • Replies 2
  • Views 21
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I would start with the doublet. Not because it is magic, but because it is the least dependent on any single matching device. A center-fed wire of roughly 100 to 130 ft, fed with 450-ohm or window line and an ATU that handles balanced loads, can cover 80 through 10 m. You mostly spend your effort on routing the feed line and choosing a length that does not give nasty impedance extremes on the bands you care about. A 4:1 current balun plus coax is a workable alternative if you want a coax entry, but then loss in the balun and the mismatched coax becomes the thing to watch.

On the EFHW side, the good ones are fine for a modest station, but quality varies. The core material, the number of turns and the compensation network all affect efficiency and heat. A 49:1 transformer that looks great on a nanoVNA at low power can run hot at 100 W on a band where the load is not close to its design impedance. The antenna is also a half wave on its fundamental and on each harmonic, so it is naturally multiband on 40, 20, 15 and 10 m. It is less natural on 30, 17, 12 and 60 m unless you add a tuner or a lucky length.

An OCFD has some of the same harmonic-pattern character. On the higher bands the pattern splits into multiple lobes, so you do not get one clean broadside pattern like a single half-wave dipole. For casual operating that is fine, but it is not a free lunch.

For the HOA part, thin dark wire, tree support at one end, and keeping the feed point and any tuner out of view can go a long way. Check the actual covenant text. In the US, PRB-1 deals with local government zoning, not private deed restrictions, so it does not give you protection from an HOA.

  • Moderators

I would also add a vertical to the shortlist, but only if the radial situation is realistic. A vertical over poor or limited ground can lose a big share of power in the ground system. A few resonant elevated radials usually beat a handful of short wires lying on the lawn, but it is still a compromise. A short loaded vertical on a mast is even more dependent on loss in the loading coil and ground. On the plus side, a vertical often hears less man-made noise than a low horizontal wire near the house, depending on the local noise source. It can be a very good low-angle DX antenna, but it can also be a very quiet way to lose signal.

As for what to measure: SWR alone is not enough. Use a modeling program such as 4nec2 or EZNEC with a realistic ground and the real height, and compare patterns. Then test on the air. WSPR or reverse beacon spots can show relative performance between two antennas on the same band at the same time of day, with the caveat that propagation changes. Check for common-mode current by touching the coax or the rig chassis at the highest-power band. If you feel RF burn or see SWR jump when you move the coax, the antenna system needs a better choke.

On coax loss, check the manufacturer's attenuation table for your cable at 28 MHz and 3.5 MHz and apply it to your real run length. Loss is manageable on a short run at low SWR, but gets worse as SWR rises or the run lengthens. That is one reason ladder line to a tuner at the radio can be a good approach when SWR is high on several bands.

For a magnetic loop, it is fine for an apartment or a spot with no other options, but remember it is high-Q and narrow. You retune when you change frequency by even a small amount, and efficiency depends heavily on conductor size, joint resistance and the capacitor. It is a legitimate stealth antenna, and the noise rejection can be a real benefit, but low bands will be a challenge.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.