Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Ghost signals and a lumpy noise floor on an SDR: overload, gain staging and antenna choice

ci_cover.jpg

A situation that comes up constantly on SDR forums: the waterfall is full of carriers that move when you change gain, or that appear in several places at once. The noise floor rises when you connect a bigger antenna. Weak signals that should be there are buried. It is tempting to blame the software (SDR#, SDRuno, GQRX, HDSDR, CubicSDR), but most of the time the cause is in the front end and the antenna system.

Start with the ADC. An RTL-SDR dongle uses an 8-bit converter, which gives a usable instantaneous dynamic range far below a 12-bit Airspy or a 14-bit SDRplay RSP. HackRF One is also 8-bit at the converter, though it has a very wide tuning range and can transmit. LimeSDR has 12-bit converters and full-duplex capability, but it is not specifically designed as a clean wideband receiver. When a strong broadcast FM or AM station reaches the ADC or the tuner's mixer, it can create images and intermodulation products that look like real signals. A quick test is to reduce the gain or insert an attenuator. If a signal drops by more than the attenuation, or moves, it is probably a product of overload, not something on the air.

Gain staging matters more than people expect. Turning everything to maximum raises the noise floor and the strong signals together. A better approach is to bring the gain up until the band noise is just visible above the receiver's own noise on a quiet part of the spectrum, then stop. On RSP hardware, the LNA state and IF gain reduction are separate controls. On an RTL-SDR, the tuner gain and the RTL AGC settings interact. Wider sample rates let more strong signals into the ADC, so a narrower bandwidth can improve things when the band is crowded.

Filtering helps even before gain tweaks. Broadcast-band notch filters, or FM and AM band-stop filters, can remove the strongest offenders. Some SDRplay models include switchable notches, and external filters are common for RTL-SDR and Airspy. For HF reception with an upconverter, the filter ahead of the mixer matters just as much as the converter itself.

On the antenna side, a longer wire is not automatically better. A random wire with a 9:1 unun brings in a lot of signal, but also much of the local noise from switch-mode supplies, LED lighting, and USB equipment. A small active loop, a magnetic loop, or a well-placed dipole away from the house can give a better signal-to-noise ratio even if the absolute signal level is lower. A common-mode choke on the coax and ferrites on USB leads often reduce the noise more than any software setting.

For discussion: what is your order of attack when an SDR looks overloaded? Do you start with attenuation, filtering, bandwidth, or relocating the antenna? And how do you decide whether an HF upconverter makes sense compared with a receiver that covers HF directly?

  • Replies 2
  • Views 25
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd begin with the overload test, because it saves time. Put a step attenuator, or software gain reduction, in line and watch the suspicious signal. A real signal drops by roughly the amount you add. An intermodulation product usually drops faster, often by about double or triple the change, depending on the order of the product. That one test separates "weak but real" from "produced by the front end" without needing any theory.

On the upconverter question: for HF on an RTL-SDR, an upconverter lets the tuner work in its normal VHF range, at the cost of an extra oscillator and mixer that can add spurs and its own images. The reported frequency is also offset by the local oscillator, so you must set the shift in the software (SDR#, HDSDR and others support this) or the dial will be wrong. Direct sampling on some RTL dongles avoids the converter, but the 8-bit ADC and the lack of selectivity mean strong shortwave broadcasters can swamp it, so a bandpass filter is worth adding. A receiver with real HF coverage, like an Airspy HF+ or an SDRplay RSP, skips that whole class of problem.

  • Moderators

One angle that's easy to miss: the noise isn't always in the radio or the antenna, it can come from the computer. USB 3 ports and cables are known to radiate broadband hash that lands on HF and VHF. Moving the dongle to the end of a USB 2 extension, adding ferrites at both ends, and powering the computer from a different supply can change the noise floor noticeably. Put the receiver at the antenna, if you can, and send the data back over a long USB or network link, instead of running a long coax into a noisy room.

The software side is useful for diagnosis too. In a waterfall, a noise source from a switching supply tends to show up as evenly spaced lines. You can also compare with a dummy load connected to the input. If the noise floor with the dummy load is well below the floor with the antenna, the noise is arriving through the antenna system. If the two are almost the same, the receiver or the computer is generating it, and no antenna change will fix that. And before you try to decode digital modes with WSJT-X, fldigi or multimon-ng, check your audio levels and the virtual audio cable. Overloaded audio is a far more common problem than a bad decoder.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.