Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dead or weak rig: what order do you check things in? Power, RX, TX, then protection circuits

ci_cover.jpg

Most rigs that "don't work" are really one of a few problems that look alike from the front panel. Here is the order I would use for a rig that is dead, deaf, won't transmit, or folds back power. I'd like to hear where others would change it.

1. Power first, and under load. A supply that reads 13.8 V on a multimeter with no load can sag badly when the rig transmits. Check the fuses in the DC cable and in the rig, then measure voltage at the rig's DC input connector while transmitting, not at the supply terminals. A big difference between the two points to a bad crimp, a corroded fuse holder, or undersized wire. Also look at the supply output with a scope on AC coupling. Excess ripple or switching-supply hash on the DC line can look like receiver noise or cause strange behaviour on transmit.

2. Separate "no receive" from "no audio" and "no transmit" from "protection". If the rig powers up but is deaf, change one thing at a time. Disconnect the antenna and see whether the noise floor changes. Check attenuator, preamp, RF gain, squelch, mode and filter settings, and any TX-inhibit or split setting in the menu. A stuck PTT line, a failed antenna relay, or a muted audio path can all mimic a dead receiver. A signal generator or a known-good nearby signal helps you work out whether the fault is in the front end, the IF, or the audio stage.

3. Use a dummy load before blaming the rig. If power drops or an SWR warning appears on the antenna but the rig behaves normally into a dummy load, the problem is likely the antenna, feedline, connector, or tuner. If it still folds back into a good dummy load, suspect the SWR detector, a drifting reference, a failed bias circuit, or a protection circuit that is reading wrongly. Bypassing protection to "see if it works" is a good way to lose the finals.

4. Blown finals are usually a symptom. Before replacing the output devices, look for what killed them: wrong bias, an open or shorted driver, overvoltage on the supply, a failed output-network capacitor, or a parasitic oscillation. Use a current-limited bench supply or a series lamp for the first power-up. Check the bias and idle current against the service manual procedure, and make sure the heatsink mounting and thermal compound are right.

5. Capacitors and contacts. Old electrolytics dry out or leak, and leaked electrolyte can eat traces, so clean it up and inspect the area after replacing the cap. Match capacitance and polarity, and use an equal or higher voltage rating. Don't swap RF-path ceramics casually, since the dielectric type matters in tuned circuits. For noisy controls, intermittent switches, and relay or connector problems, a proper contact cleaner applied sparingly is worth trying before replacing parts. Check PL-259 centre pins and DC plugs too.

6. Alignment last. Don't touch trimmers unless the symptoms or measurements point to drift. If you do, write down or photograph the original settings, use a non-metallic tool, and follow the manual with the right instruments: signal generator, frequency counter, wattmeter, and dummy load.

What would you do differently, and which test instrument do you think gives the most diagnostic value for the money?

  • Replies 2
  • Views 29
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I agree with the dummy-load step, and I'd add a reminder that a rig's SWR meter or protection circuit is only as good as its directional coupler. If the forward and reflected detector diodes have drifted, or a connector inside the rig has a poor joint, the rig can report high SWR into a perfectly good load. Test that with a known-good dummy load and, if possible, an external wattmeter that you trust. If the external meter shows sensible power and low reflected power but the rig still cuts back, the fault is likely inside the protection or sensing circuit.

Also watch the order of the checks you mention in step 2. A relay that clicks is not necessarily making good contact. A multimeter on continuity or resistance across the relay contacts, with the rig powered down and the antenna disconnected, can show whether a path is actually closing. For RF voltage measurements, remember that a standard DMM can read incorrectly in the presence of RF, so an RF probe or a scope is the better tool there.

  • Administrators

On blown finals, the point I would stress is not to power the rig fully until you've done the bias check. New transistors in a circuit with the wrong bias or a shorted driver can fail immediately. A current-limited supply, or a lamp in series with the supply, gives you a chance to see excess current before damage happens. If the amplifier uses matched pairs or specific device types, use the correct replacement parts and follow the service manual's bias setup.

For the scope, a 10x probe with a short ground spring gives much more trustworthy results than the long clip lead. On transmit into a dummy load, look for a clean RF envelope, flat-topping, or an oscillation that appears without drive. The service manual is also the best tool for finding test points and expected voltages, so check whether the manual covers your exact revision. A schematic from a different version of the rig can send you after the wrong component.

Finally, be careful with capacitors if the rig has a switching regulator. The ESR and ripple rating of the replacement can matter as much as the capacitance and voltage. A basic ESR meter is a useful addition to the bench alongside the multimeter and scope.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.