Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a 100 W HF shack: rig choice, power, tuner placement, bonding and filtering

ci_cover.jpg

A practical discussion thread for anyone building or rebuilding an HF base station. The aim is to separate what the transceiver decides from what the rest of the station decides. Plenty of problems blamed on a rig, like noise, RF in the audio, or a tuner that won't settle, trace back to the power supply, feedline, bonding or antenna system instead.

Here is a typical scenario to work from. It is a 100 W station on a mix of a multiband wire antenna and a vertical, with a possible amplifier later, a desk shared with a computer and monitor, and a house with ordinary mains wiring. Common candidates are the Icom IC-7300 or IC-7610, Yaesu FT-991A or FTDX10, Kenwood TS-590SG or TS-890S, and Elecraft K3S. The KX3 and Xiegu G90 sit in the portable and low-power category but often end up as home stations too.

Some questions to get started:

1. Which receiver traits matter for your band conditions? Dual receive, roofing filter options, and strong-signal handling matter far more on a crowded contest weekend than for casual SSB or FT8. A single-receiver radio can be a great fit if you never need diversity or split-band listening.

2. How well does your antenna match the rig's internal tuner? Internal tuners are generally designed for modest mismatches, not for a long run of coax with a high SWR. If the antenna is far from the radio, a tuner at the feedpoint, or a resonant or balanced design, often beats tuning in the shack.

3. Where will you put RF-sensitive and noise-generating gear? Switching supplies, USB hubs, monitors and LED lighting all radiate. Layout can matter as much as the choice of radio.

Please post the radio, antenna type and feedline length, supply type, and whether you plan to add an amplifier or a second receive antenna. Check the manufacturer's manual for exact specs before relying on anything quoted in this thread, since details vary between models and firmware versions.

  • Replies 2
  • Views 29
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the rig question, it helps to sort the radios by architecture and use case instead of trying to rank them. The IC-7300 uses a direct-sampling SDR design, and the IC-7610 builds on that with two receivers and two ADCs, which is the real draw for split-band listening and diversity. The TS-890S and K3S are traditional down-conversion superhets with selectable roofing filters, which is why they come up so often in crowded-band and contest discussions. The FTDX10 sits in between with a hybrid design. The FT-991A adds VHF/UHF coverage in a compact radio, so it fits a mixed-band station where HF performance is not the only priority. The G90 and KX3 are lower-power radios with different aims, a small portable station versus a compact 5 to 10 W QRP rig, so they shouldn't be judged on the same terms as the 100 W radios.

For the power supply, a 100 W radio typically needs a 13.8 V source rated around 20 to 25 A. A nominally 30 A supply gives useful headroom. The thing people overlook is voltage drop in the DC cable. A long or thin run can pull the voltage down during transmit peaks and cause distortion or reduced output. Use a heavy-gauge cable, keep it short, fuse the positive lead close to the source, and follow the radio manual for the fuse rating.

Switching supplies can radiate hash on HF. If you hear noise that changes when you unplug the supply, try ferrite chokes on the DC and AC leads, or try a different supply or a battery as a test. A linear supply is heavier but quieter in most cases. Test before you buy, because individual units vary.

  • Administrators

On grounding and bonding, it's worth separating three jobs that often get lumped together as "the ground." Safety grounding is the mains equipment ground. Lightning protection means giving surges a controlled path to earth, ideally with an entry panel and arrestors bonded to a single point. RF grounding is a separate matter. A rod outside the window is not a magic fix for RF in the shack. For HF, the more reliable approach is to keep RF out of the shack to begin with, using a common-mode choke at the feedpoint, a balanced antenna or a decent radial or counterpoise system for a vertical, and chokes on the coax at the shack entry.

Inside the shack, bonding the chassis of the radio, amplifier, tuner and power supply to a common bus with short, wide straps is good practice. It reduces potential differences and helps with stray RF. If you then get hum or noise through USB or audio cables, a ground loop is a likely culprit. Ferrites, USB isolators, or reworking how the computer and radio share their ground paths are typical fixes. For lightning and electrical-code questions, follow your local code and consider a qualified electrician, because bonding the antenna system to the service ground is a safety matter, not just an RF one.

On tuners: an amplifier should see a reasonably low SWR, so put the tuner in the right place in the chain and don't rely on it to hide a bad antenna. If the SWR on the coax is high, the tuner can make the radio happy while loss in the feedline eats the power. Band-pass filters usually matter most in multi-transmitter setups, like contest stations running two radios on the same band at once, or when a strong nearby transmitter overloads the receiver. For a single-radio station with one antenna per band they are often unnecessary, so look for a specific problem first.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.