Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Small-yard multiband HF wire: EFHW vs OCFD vs G5RV vs doublet, and what really decides performance

ci_cover.jpg

Many threads on stealth and small-lot HF antennas turn into a brand argument. It may help to compare the options on the things that actually change the signal: where the current flows, how high the radiating part is, how much loss sits in the feedline and matching device, and how much common-mode current ends up on the coax. Here is a framework to push on, and I'd like corrections.

First, SWR is a matching number, not an efficiency number. A dummy load shows 1:1 and radiates nothing. A vertical over a poor radial field can also show a pleasant SWR because ground loss adds to the feedpoint resistance, which moves it toward 50 ohms. A wire with a 4:1 SWR at the antenna end of a short, low-loss feedline can radiate better than a lossy compromise that reads 1.2:1. SWR only tells you how much power gets into the system. It doesn't tell you how much leaves as RF.

The common wire options sort out roughly like this. An end-fed half-wave (EFHW) presents a very high impedance at the end, often a few thousand ohms, so it needs a transformer with a ratio around 49:1 to 64:1. A half-wave on 40 m also behaves as a half-wave on harmonically related bands such as 20, 15 and 10 m. It does not cover 30 m or 17 m without extra tricks. It is convenient because there's no need to get a feedline to the center of the span, but the coax usually becomes part of the antenna system unless you add a counterpoise or a choke. The transformer core, winding and any compensation capacitor all affect loss and bandwidth, and the loss can be significant at higher power.

An off-center-fed dipole (OCFD, or Windom type) feeds a half-wave wire at roughly the one-third point through a 4:1 or similar current balun. It tends to give usable matches on several harmonically related bands, but the match on a given band depends heavily on exact dimensions, height, and surroundings. The radiation pattern also changes with the band, because on harmonics the current distribution shifts. Common-mode current on the feedline is a real concern here as well, and a choke is cheap insurance.

The G5RV is a roughly 102 ft (31 m) wire with a section of balanced line (about 34 ft) leading to a coax run. It is not a resonant, matched-everywhere antenna. It is a multiband doublet that you tune with an ATU, and the ladder-line section does the work of carrying the mismatch. It is usable but not magic. Its behavior on a given band depends on whether you land at a friendly impedance. Put a choke at the ladder-to-coax transition.

A plain doublet fed with open-wire or window line is the most forgiving approach for loss, because balanced line has far lower loss than coax at high SWR. The price is that you need a balanced-capable tuner, or a tuner plus a good balun, and the line has to be routed into the shack away from metal, which is the hard part in a small yard. Choosing the length so you avoid extremely high or low feedpoint impedances on your favorite bands helps the tuner.

An inverted V is a useful way to fit a dipole on a single mast. A wide apex angle (somewhere near 90 to 120 degrees) keeps the feedpoint near 50 ohms. The legs are slightly shorter than for a flat-top because of end loading and the droop. The tips are high-voltage points, so keep them well above head height. Height matters here: a horizontal wire below about a quarter wavelength mostly sends energy high, which is fine for NVIS-style work on 80 or 40 m but less fine for DX on the higher bands.

Verticals and loops are a different trade. A quarter-wave vertical lives or dies by its ground system. A few elevated, resonant radials can outperform a larger number of short buried radials, and a ground-mounted vertical typically needs a lot of radials before ground loss comes down. A small magnetic loop can be a reasonable stealth option, with a very narrow bandwidth that you must retune, high circulating currents and voltages, and efficiency that depends on the conductor, joints and capacitor. Many people find they also reduce local noise on receive, which can be as valuable as transmit gain if the noise floor is what is holding you back.

For HOA or deed-restricted lots, the stealth part is usually physical. Thin dark wire, trees as supports, a vertical disguised as a flagpole or garden fixture, and a loop that can be put out and taken down can all be practical. Check the actual covenant language. In the US, PRB-1 covers state and local government regulations, but does not by itself override private deed restrictions. Don't let stealth override safety: stay well clear of power lines, plan lightning protection, and keep RF exposure limits in mind for any antenna near living space.

Question for the thread: if you only get one horizontal wire and a tuner, do you spend your effort on getting the wire higher, on getting the feedline loss down, or on common-mode control at the feedpoint? And does a 40 m EFHW make sense as the primary antenna on a lot where a center-fed wire can't be run?

  • Replies 2
  • Views 266
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

If the goal is the broadest band coverage with the fewest surprises, I'd rank the center-fed doublet on ladder line first, purely on loss physics. Open-wire line barely cares about a 10:1 or 20:1 mismatch, and coax does. The usual objection is routing, but the line doesn't need to be pretty. It needs to be kept a few inches off metal, avoid running parallel to gutters or siding for long distances, and cross other conductors at right angles. A wire you can feed at the center also gives a symmetrical pattern, which makes modeling easier to trust.

The catch is the transition at the shack. A balanced tuner or a 4:1 voltage/current balun with a choke should be matched to what the line actually presents. A balun built for a 50-ohm resistive load doesn't necessarily behave when it sees a few hundred ohms of reactance. A tuner's internal balun can saturate or get hot on certain bands, so watch for that before blaming the antenna. A modeling program such as EZNEC or 4nec2, with a real ground model and your actual wire heights, will show which bands land at awkward impedances before you cut anything.

On the G5RV, I'd call it a doublet with a particular length ratio, and I'd treat it like one. The 34 ft of ladder line is not special to every band. If you already own one, run it with a choke and a tuner and compare on-air reports across bands rather than relying on the tuner meter.

  • Moderators

The EFHW question deserves a straight answer. On a lot where you can only run one wire along a fence line or up to a tree, an EFHW has an obvious practical advantage: one feedpoint, one coax, no center support. The things to look at are the transformer's core size and mix relative to your power, whether the manufacturer says anything about common-mode handling, and where the coax goes. In many installs the outside of the coax carries real current, so a choke a short distance from the transformer, and perhaps another near the shack, keeps the RF out of the house and the pattern more predictable. A thin-wire EFHW at a low height can still work well for contacts, but its coverage is band-limited, and a modest ATU helps on bands where it's off-resonance.

One thing I'd push back on is chasing SWR on a vertical. If a ground-mounted quarter-wave shows a nearly flat match with only a handful of radials, that may mean it's burning the missing power in the ground. Measure the feedpoint resistance with an antenna analyzer and compare it to the expected figure. Lower resistance with more radials is usually the sign you are improving efficiency, even though the SWR number may look worse. That's the opposite of what intuition suggests.

For comparing antennas honestly, side-by-side tests with a fast A/B switch on received signals, or comparing spot reports on a mode like FT8 or WSPR on the same band and time, tell you more than SWR sweeps. They still carry plenty of variability from propagation, so treat any single comparison as indicative, not definitive.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.