Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Checking a homebrew QRP transmitter for harmonics with basic bench gear

ci_cover.jpg

Many homebrew transmitters, whether a Tuna Tin 2 style crystal oscillator and PA, a Pixie, or a BITX or uBITX with a modified output stage, are built to the point where they make RF into a dummy load and then go straight on the air. The step in between is checking what else is coming out of the connector. This thread is about doing that with modest equipment.

Start with why it matters. Simple transmitters often drive the final with something close to a square wave, and the final may run class C or hard-saturated class E or C-like. An ideal square wave has a third harmonic at about one third of the fundamental's voltage, which is roughly 9.5 dB down. A 7 MHz rig with no output filtering can put real power on 21 MHz. The simple low-pass networks in small designs are often marginal, and the result depends on the actual toroids, the layout and the load.

For a baseline, put the rig into a 50 ohm dummy load and check the power. A 5 W carrier into 50 ohms is about 15.8 V RMS, or roughly 44.7 V peak-to-peak. A 1 W carrier is about 7 V RMS, or 20 V peak-to-peak. These are useful sanity checks if you have a scope with enough bandwidth and a proper 10x probe. A scope will show you waveform distortion, but it is a poor tool for putting a number on harmonics that are 40 dB or more down.

Here are some options for measuring harmonics, roughly in order of increasing capability:

1. A second receiver. Tune it to 2x and 3x the operating frequency while the transmitter runs into a dummy load. A strong signal there is a warning, but only a qualitative one, because the receiver front end and AGC are not calibrated.

2. An SDR with a fixed attenuator chain in front of it. Use a known-good attenuator, 30 dB or more depending on power, and a directional coupler or resistive tap rather than connecting the transmitter straight to the input. You can compare the fundamental and the harmonics, but check that the attenuator and the SDR front end are not overloaded, or the harmonics you see may be created in the receiver.

3. A spectrum analyzer. This is the proper tool, again with a pad in front of it. Many regulators specify the limits as a number of dB below the mean power of the fundamental, and the required figure varies by country and power level, so check your own rules instead of relying on a rule of thumb from a forum.

Which test gear would you prioritize first if the budget is tight: a decent scope, a NanoVNA for filter checks, an SDR for spectral checks, or a calibrated power meter? And has anyone compared the measured filter response against the calculated response for the low-pass filters used in common kit transceivers?

  • Replies 2
  • Views 24
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

If I had to choose a single instrument for this job, I'd pick something that tells you about the filter before the transmitter is connected to it. A NanoVNA or similar is very good for measuring a low-pass filter on its own: cutoff, passband loss, and how fast the attenuation rises at 2f and 3f. That lets you fix the filter before you ever apply RF drive.

For measuring the transmitter itself, a dummy load and some kind of RF power indication is the other essential. A diode probe on a scope or DMM, or a simple SWR bridge that you've checked against a known source, gives you relative readings, and relative is enough for tuning. Just remember the diode drop makes low-level readings non-linear, so don't trust the absolute numbers at 100 mW the way you would at 5 W.

One more caution about the SDR method: use more attenuation than you think you need. A second harmonic that appears only because the SDR front end is overloaded can send you chasing a problem that isn't in the transmitter. Change the attenuator by 10 dB and see whether the apparent harmonic drops by exactly 10 dB. If it drops by more, it's partly being generated in the receiver.

  • Moderators

On the filter side, the calculated values in the schematic are only the starting point. Real toroids don't land exactly on the value you wound, so the cutoff can shift. Start from the core's AL value (L = AL × N²), wind to the calculated inductance, and then measure the filter. Powdered iron cores such as the T37-6 or T50-6 families are common in QRP filters, and the exact core mix matters, so match the part number to the design.

For the capacitors, use C0G/NP0 ceramics or silver mica. Cheap general-purpose ceramic types can change value with voltage and temperature, and that shows up in filter response. Also look at layout: leave a little room between the toroids so they don't couple to each other, and keep the input and output leads of the filter physically separated, otherwise some of the signal bypasses the filter and your stopband attenuation is much worse than the design predicts.

For multiband rigs such as the BITX or uBITX family, the filtering is relay-switched or band-selected, so you should measure each band separately. The upper bands tend to be the ones where a filter that looks fine at the lower frequencies is least effective, because the harmonic spacing and the transmitter's spurious content are different there.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.