Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

No TX, no RX, or both? A triage order for dead rigs (and where it usually goes wrong)

ci_cover.jpg

A lot of repair threads jump straight to "the finals are gone" or "the PLL is bad" before anyone has confirmed the radio is getting clean DC. I'd like to lay out a triage order and then hear where people would change it. The goal is to avoid chasing a symptom that is really a supply, connector or control-line problem.

1. Power, measured under load. Check voltage at the rig's DC input while it is transmitting, not just at the supply terminals. A fuse holder with a corroded clip, a crimped lug that has gone high-resistance, or a thin cable can read 13.8 V at the supply and sag well below that at the radio. A decent bench supply with a current meter tells you a lot: a rig that draws far too much current at idle points to a shorted stage or a failed capacitor, and one that draws almost nothing points to a missing rail, a dead regulator or a processor that never starts.

2. Dead on both TX and RX. This usually means something common to both paths. Look at the main regulators, the reset and microcontroller, the reference oscillator and PLL lock. If the display is alive but nothing works, look at the synthesizer: an unlocked PLL or a missing reference will kill both receive and transmit. A scope or a frequency counter on the reference oscillator is a quick check.

3. RX only dead. Check audio first. Is there noise at the volume control with the squelch open? If audio is fine but the S-meter never moves, work backwards from the antenna: antenna relay, front-end filters, first mixer, IF filter. Injecting a signal from a generator at successive stages shows where the signal disappears.

4. TX only dead. Separate the PTT and switching logic from the RF chain. Confirm the PTT line actually changes state, that the TX/RX relays or diodes switch, and that the driver and final stages get their bias and supply. Then try a dummy load. If the radio makes power into a dummy load but folds back on the antenna, it is working as designed and the antenna system is the fault.

What would you add or reorder? Particularly interested in how people handle the intermittent faults that disappear as soon as the cover comes off.

  • Replies 2
  • Views 21
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

The order is good. I'd add one thing to step 4: when the SWR protection is suspect, put the rig into a known-good dummy load and compare its SWR and power readings against an external wattmeter. Protection circuits rely on a directional coupler, usually a small toroid or a pair of detector diodes feeding a DC amplifier. If a detector diode has gone leaky or a trimmer has drifted, the radio can believe it sees high reflected power and cut output when nothing is wrong. That looks exactly like a weak or dead transmitter.

On blown finals, the dangerous mistake is swapping the transistors and applying full drive. Finals rarely die alone. Common causes are a bias circuit that has drifted or failed, a failed driver, a poor supply, an open or damaged protection path, or a parasitic oscillation. Before applying RF, check the bias network and set the idle current to the service manual figure with no drive. Use a current-limited supply and bring the voltage up gradually. Also treat replacement devices from open marketplaces with caution, since relabelled and counterfeit RF transistors are a known problem, and a part that does not match the original's gain and ratings can destroy itself quickly.

  • Moderators

On the intermittent faults: a plastic stick or a chopstick is cheaper than most test gear. Gently pressing on boards, connectors and ribbon cables while the rig is running often shows a cracked joint or a flaky connector. Contact cleaner can help with dirty switches, rotary contacts and pots, but use it sparingly. Soaking a board can leave residue, and some old pots do not enjoy being flooded. Isopropyl alcohol and a soft brush are enough for most board and connector cleaning.

For capacitors, I'd measure before replacing. An ESR meter, or a meter with in-circuit ESR capability, makes the job much more targeted. Switching supplies and DC-DC converters are the usual places where tired electrolytics cause noise, hum, hash on receive or unreliable start-up. When replacing, match capacitance, use equal or higher voltage rating, observe polarity, and choose low-ESR, suitable-temperature parts where the circuit needs them. If an old SMD electrolytic has leaked, clean the residue thoroughly and inspect the traces, because the electrolyte can eat copper and cause faults that remain after the new part is fitted.

Finally, don't touch alignment unless there is a reason. If a fault is not clearly an alignment issue, you can make things worse. When you do align, use the service manual procedure with a dummy load, a power meter, and a signal generator, or at least a counter and a known-good reference. A scope is useful for seeing oscillator amplitude, audio distortion, ripple on rails and switching noise, which a multimeter will average out and hide.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.