Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Scratch-building a 40 m wire dipole or vertical: wire, feedpoint, choke, supports, and checking it with a model and an analyzer

ci_cover.jpg

This thread is for the practical decisions in building an HF wire antenna from raw materials rather than buying a kit. A 40 m half-wave dipole and a 40 m quarter-wave vertical make good worked examples because both are simple enough to model and build, and both show up the usual problems: mechanical failure, common-mode current on the coax, and trusting an SWR reading more than it deserves.

Start with the numbers. A half-wave dipole is roughly 468 / f(MHz) feet overall, so about 66 ft at 7.1 MHz. Treat that as a starting length, not a final one. Insulated wire resonates lower than bare wire, an inverted-V resonates a little lower than a flat-top, and nearby trees, roofs and ground height all pull the frequency around. Cut long, then trim a bit at a time while watching the resonance on an analyzer. A quarter-wave vertical is about 234 / f(MHz) feet, around 33 ft for 40 m, plus a radial system, which is where most vertical performance is won or lost.

For wire, 14 AWG hard-drawn copper or copper-clad steel is a common choice for permanent spans because it resists stretching. Plain soft-drawn copper sags and can slowly stretch until the resonance shifts. Stranded wire is easier to handle and kinks less, but is often heavier or weaker for its gauge. Resistive loss in 12 to 16 AWG at HF is small for a dipole, so choose on strength, weight and weather resistance rather than electrical loss.

At the feedpoint, take the mechanical load off the connector. The wire tension should go through the insulator or center plate, and the coax should be strain-relieved so it doesn't hang from an SO-239. Seal the connection against water, and leave a drip loop below it. At the ends, use UV-stable insulators and UV-stable polyester rope, not whatever cord is nearest. If you hang the end from a tree, a pulley with a weight or a spring takes up movement so the wire doesn't break in wind.

Questions I'd like to hear opinions on: Would you feed the dipole with coax and a choke, or with 450-ohm window line and a tuner? How much do you trust an EZNEC or MMANA model compared with measurements at the real site? And for a vertical, how many radials do you consider enough when you can't bury dozens of them?

  • Replies 2
  • Views 111
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the feed question, both work, and the choice depends on whether you want a single-band antenna or one that covers several bands. For a single-band 40 m dipole, coax with a 1:1 current balun or a choke at the feedpoint is the simplest setup. The goal of the choke is high common-mode impedance, so the outside of the coax shield doesn't become part of the antenna and radiate or pick up noise. Type 31 ferrite is a common choice for the lower HF bands. Roughly 8 to 12 turns of small coax through a large toroid, or a stack of clamp-on or bead cores over the cable, is a typical construction. A coil of coax with no ferrite can also work as a choke, but its useful bandwidth is narrower and it is better suited to higher frequencies than to 80 or 160 m.

If you want multiband use from a single wire, open-wire or window line makes sense. Ladder line has low loss even when the SWR on it is high, which is why it pairs well with a dipole used on bands where it isn't resonant. The cost is that you need a tuner that can handle the resulting impedances, plus a balun or a balanced tuner at the shack end. Keep the line away from metal gutters and downspouts, and bring it away from the antenna at right angles for a distance. Some line lengths on certain bands give very awkward impedances at the tuner, so it is worth modelling the actual length rather than assuming any length will tune.

One extra tip for measuring: when you check an antenna with an analyzer connected through coax, common-mode current on the shield can change the reading when you touch or move the cable. If the reading changes as you move your hand along the coax, that tells you the choke isn't doing enough.

  • Administrators

On verticals and radials: a ground-mounted quarter-wave depends heavily on its radial field. A small number of radials on or in the ground gives a lossy system, and more radials help up to a point of diminishing returns. If you can't bury a lot of wire, a raised design with a few resonant radials, a quarter-wave long and a few feet or more above the ground, is a reasonable compromise. Sloping the radials downward tends to move the feedpoint impedance closer to 50 ohms, while horizontal ones tend to give something lower, so you can use the slope as a rough matching adjustment. A fiberglass pole is convenient for supporting the vertical wire. It doesn't interact with the antenna the way a metal mast does, but tape or clip the wire on carefully so it doesn't slide with wind.

For traps, the idea is that a parallel LC circuit tuned to the higher band behaves like an open circuit there, isolating the outer wire. On the lower band the trap acts like an inductor, so it loads the antenna and lets the elements be shorter than full-size. The tradeoffs are narrower bandwidth, some trap loss, and the need to tune each trap before it goes into the antenna, ideally with an analyzer or a dip meter. A fan dipole or several separate dipoles on one feedpoint avoids traps entirely, though the wires interact, so you often have to adjust them together.

For modelling, both EZNEC and MMANA-GAL are useful when you keep their limits in mind. Watch segmentation, junction geometry and the ground type. In NEC-based programs the average gain test is a good sanity check for a model that has gone wrong. Neither program knows about the tree beside your end support, the house wiring or common-mode current on your coax unless you add them. Use the model to compare ideas and predict trends such as inverted-V angle, height or a trap's effect on length, then trust the measurement for the final trim. Also remember that a low SWR doesn't mean an efficient antenna, since a dummy load has a perfect SWR. Measure at the feedpoint if you can, because coax loss can make the far end look better than the antenna really is.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.