Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Picking a VHF/UHF antenna: J-pole, slim jim, 5/8 whip, collinear or yagi, and where the dB really go

ci_cover.jpg

Antenna choice on 2 m and 70 cm tends to turn into a gain-number contest. The spec sheet says 6 dBi, so it must beat the 3 dBi antenna. In practice, pattern shape, polarization, feedline loss and the installation matter at least as much as the headline figure. This thread is for comparing the common designs and the practical details around them.

Quarter-wave whip. The simplest vertical is a quarter-wave radiator over a ground plane. On 2 m the element is about 19 inches (roughly 48 cm), and on 70 cm about 6.5 inches. It has a low-angle pattern, a feedpoint impedance close to 50 ohms, and little to go wrong. It needs a decent ground plane, which is why a roof-center NMO mount works so well. A mag mount on a small or curved surface gives a lopsided pattern and a less predictable match.

5/8 wave. A 5/8-wave vertical usually needs a matching coil at the base. It concentrates energy a little closer to the horizon than a quarter-wave, so manufacturers typically quote about 3 dB over a quarter-wave. That figure assumes a good ground plane. On a small plane, or a vehicle with a sloping roof, the real-world difference shrinks and the pattern can tilt upward. A 5/8-wave also depends more on the coil and the mount than a quarter-wave does.

J-pole and slim jim. Both are end-fed half-wave designs with a quarter-wave matching section, so they need no radials in principle. In practice the outside of the coax can carry current and distort the pattern and SWR. A choke, such as several turns of coax or a ferrite sleeve at the feedpoint, often helps more than trimming the antenna. A slim jim is essentially a folded variation that gives a somewhat lower takeoff angle. The gain difference between a well-built J-pole and a slim jim is small, and construction accuracy and feedline decoupling matter more than which one you build.

Collinears. Stacked in-phase half-wave sections compress the pattern vertically, trading elevation beamwidth for gain. That is great for a repeater or base station on flat terrain, but a very long collinear can leave nearby or elevated stations in a null. Whip mounted on a hill or tall building often suffers from this, so more gain isn't always better for the coverage area you want.

Yagis. A 3-element yagi gives somewhere around 7 dBi and a 5-element around 10 dBi, with a front-to-back ratio that helps reject interference. Use vertical polarization for FM and repeater work, and horizontal for SSB and CW weak-signal operation. Cross-polarized signals can lose 10 to 20 dB or more, though reflections make the real figure vary a lot.

Feedline and connectors. At VHF/UHF, coax loss climbs quickly with frequency. Small cable such as RG-58 is acceptable for short runs, but at 70 cm over 50 to 100 ft it eats a large share of your power and your receive signal. Larger low-loss cable such as LMR-400 type or RG-213 is a better choice for longer runs. Check the manufacturer's datasheet for the frequency you use. The PL-259/SO-239 (UHF connector) is fine on 2 m and common on HF, but it is not constant-impedance and is a poor choice at 70 cm and above. An N-type is better matched, better sealed and a better fit for outdoor UHF installations. Whatever you use, weatherproof the joint properly, because water in coax can ruin it.

SWR. A low SWR means the antenna system presents a good match to the transmitter. It does not mean the antenna is radiating efficiently. Lossy coax can make SWR read well at the radio end while much of the power is turned into heat. To judge the antenna itself, compare readings at the feedpoint and at the radio, or use an antenna analyzer.

What are people running, and what compromises have they found worth making? I'm especially interested in mobile mounting choices (NMO vs mag mount), repeater-site antenna spacing, and what works for satellites with a handheld versus a dedicated crossed-yagi setup.

  • Replies 2
  • Views 18
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On mobile installs, the mount usually matters more than the antenna on top of it. An NMO mount, which needs a 3/4 inch hole, gives you a solid electrical connection to the body and a repeatable ground plane. Placing it in the middle of the roof gives the most symmetrical pattern. A trunk-lid or fender location tilts the pattern and can reduce gain in some directions. A mag mount is a fair compromise if you can't drill. Clean the surface and the magnet, avoid routing the coax in a way that pinches it in a door or hatch, and remember that the coupling is capacitive, so it depends on the area under the magnet. Also lift it now and then and wipe off grit, which can scratch the paint.

For a 70 cm mobile, a 5/8-wave or even a collinear-style whip can be a nice step up from a quarter-wave, but on a vehicle with a lot of roof curvature, check the SWR across the band and the actual performance rather than trusting the label. Cable length matters too. Excess coax coiled up behind a panel is fine, but a very long run of thin cable on UHF is a loss that no antenna gain will fix.

  • Moderators

On repeaters and satellites, polarization and isolation become the main design issues. Most FM repeaters use vertical polarization, so a vertical omni such as a collinear at the top of the tower is typical, with the duplexer and filtering handling the isolation between transmit and receive. If you use separate transmit and receive antennas, vertical separation is much more effective than horizontal separation at getting the required isolation. A few feet of vertical spacing can be worth a lot more than the same distance sideways.

For satellites, linear polarization can be a poor match because the satellite's orientation and the Faraday rotation of the signal change the polarization you see. That is why dedicated satellite antennas are often circularly polarized, or crossed yagis fed to produce circular polarization, with a rotator for azimuth and elevation. For the strong FM satellites, a small handheld yagi with a handheld radio can work, because you can twist the antenna to find the best polarization as the pass goes on. A fixed vertical whip may work for brief high-elevation passes, but expect deep fades and a shorter usable window.

Also keep a yagi or any directional antenna well clear of metal masts and other antennas close to it. Mounting the boom behind a metal mast or too close to a rooftop structure can distort the pattern and shift the match more than people expect.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.