Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Before you key up on a linked repeater: offsets, tones, time-outs and what's on the other end

ci_cover.jpg

A lot of repeater problems come down to a handful of settings and habits that nobody explained at the start. This thread is meant to collect the practical basics in one place, from programming a new memory to knowing what you might be talking into once a repeater is linked. Corrections and local differences are welcome.

Offset and tones. A repeater receives on one frequency (its input) and transmits on another (its output). Your radio listens on the output and transmits on the input. The difference is the offset, and the usual values depend on band and region. In the US, 2 m is typically 600 kHz, positive or negative depending on where in the band the pair sits, and 70 cm is typically 5 MHz. Other countries and IARU regions use different splits, so check your national band plan or a current local listing rather than assuming. Most radios can set the offset automatically, but the automatic choice is only a guess based on the band plan, so verify it.

Most repeaters also require a CTCSS tone (often called PL, a Motorola trademark) on the input before they will open. The tone is sub-audible, usually between about 67 and 254 Hz. Some repeaters use DCS, which is a digital code sent along with your signal instead of a continuous tone. The most common mix-up is between the tone you send and the tone you decode. Setting your radio to Tone (encode only) sends the tone to open the repeater. Setting it to Tone Squelch (TSQL) or DCS also makes your receiver stay muted until it hears a matching tone. That is useful for cutting noise, but it can hide a repeater's audio if the output tone differs from the input tone. If you can hear nothing, try turning decode off. Be aware that a tone is for access control and interference rejection, not privacy. Anyone can hear the output without it.

Linked systems. Many repeaters are connected to other systems, and what you transmit may go further than the local coverage area. The main types are:

EchoLink is a VoIP system that requires callsign validation, and nodes are reached by number. IRLP is also Internet-based, using node numbers and DTMF control, and often links through reflectors. AllStar is built on Asterisk and app_rpt, and its nodes can be linked and hubbed in flexible ways. Wires-X is Yaesu's system for System Fusion (C4FM) radios and uses nodes and rooms. DMR repeaters use time slots, color codes and talkgroups, and your radio needs a programmed Radio ID. D-STAR uses callsign-based routing, with fields such as MYCALL, URCALL and RPT1/RPT2, and can connect to reflectors. Analog FM repeaters can be tied into any of these through a gateway, so the same transmission may be heard on several systems at once.

Open, closed and coordinated. An open repeater is available to any licensed amateur within the rules. A closed or limited-access repeater restricts use to members or approved users, often through a tone that is shared only with them. That is the owner's call, and the tone is not something to pass along. Coordination is the process where a recognized frequency coordinator (the arrangement varies by country and region) helps avoid putting repeaters on the same or adjacent pairs where they'd interfere with each other. Where coordination exists, it protects everyone's coverage, though in some places it is voluntary or informal.

Time-out timers. Most repeaters have a time-out timer (TOT) that drops the transmitter if one transmission runs too long. Typical settings are a few minutes, but they vary. Many repeaters also have a courtesy tone that sounds after each over and signals that the timer has reset. Keep your overs short, wait for the courtesy tone, and if the timer trips, the repeater may need a moment before it will accept a new transmission.

Etiquette basics. Listen before transmitting, because the repeater may be busy, running a net, or linked to a distant system. Leave a short pause between overs so others can join or break in. Identify as your licence requires, and use your callsign rather than "CQ" on repeaters, because repeaters are for local contacts. Say "monitoring" or give your callsign plus "listening" to indicate you're open for a call. Avoid kerchunking, which is keying up just to see whether the repeater opens. It is better to give a brief callsign and ask for a signal report. And keep in mind that repeater autopatch, if it exists, is subject to your national rules about content and third-party communications.

Finding repeaters. Online directories such as RepeaterBook, regional coordinator lists, national society listings and local club websites are the usual sources, along with printed directories in some countries. Any list can be out of date, so confirm offset, tone, mode and access policy before relying on an entry, and check the owner's club page if the entry is unclear. Clubs often maintain these repeaters through dues and volunteer work, so joining and contributing is one useful way to keep them on the air.

What else should a new user know before their first transmission, and what local differences should people check for?

  • Replies 2
  • Views 15
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One addition on tones. When a repeater listing shows two tone values, they are often the input (the tone you transmit) and the output (the tone the repeater may send). A lot of directories list only one, and that one is usually the input. If the repeater seems to be working but you can't hear it, check whether your radio is in a decode mode. In some radios the labels are confusing, for example "Tone", "TSQL", "DTCS" and "Cross", so read the manual rather than guessing at the menu names.

Offsets are the other frequent trap. Radios that auto-set the shift from the band plan can be wrong for a particular repeater, especially anywhere the pair doesn't follow the local convention. If the listing says the shift is something unusual, set it manually. Also double-check the sign. A plus when it should be a minus will not open the repeater.

For linked systems, a rule of thumb that holds up is to assume someone else may be listening far away. Pause longer than you think necessary, particularly on a system running through EchoLink, AllStar or a reflector, because Internet delay can add to the usual gap between overs.

  • Moderators

On digital modes, the setup is where most people stumble, so here is a short checklist. For DMR, you generally need a registered DMR ID programmed into the radio, the correct color code, the right time slot, and the talkgroup you actually want. If any one of those is wrong, you may key the repeater without anyone hearing you. Check the network the repeater uses, since talkgroup numbers are not universal across networks. It's also polite to listen for a while first, because a talkgroup may be a busy, wide-area one and many hotspots may be on it.

D-STAR and Wires-X are different again. D-STAR relies on correctly entered callsign fields, and routing to a reflector or another user depends on getting URCALL and the repeater fields right. Wires-X operation depends on the node or room you connect to and on the repeater's local policy. In every case, the repeater's owner or club page is the best source for the correct settings and any rules about linking, because those vary a lot.

Finally, a note on mixed systems. Some sites run analog FM alongside digital modes, or connect an FM repeater to a digital network through a gateway. If you hear odd audio or a long delay, it may be a link rather than a fault. When something is truly wrong, the polite step is to contact the repeater's trustee or club using the details on their page, rather than discussing it on the air.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.