Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

First LEO satellite station: FM birds, RS-44 linear, ISS and QO-100 — what matters for tracking, Doppler and antennas?

ci_cover.jpg

This is a starter thread for anyone moving from terrestrial VHF/UHF into satellite work. The hobby looks like a pile of unrelated tools: Gpredict or SatPC32, an Arrow or a Yagi, a rotator, grid squares, and a list of satellite names. In practice it comes down to three questions. Where is the satellite? What frequency should I be on right now? Can I point something useful at it? Everything else follows from those.

Start with the type of bird, because it decides your workload. FM satellites such as SO-50, AO-91 and AO-92 work like a fast, moving repeater. You transmit on one band and listen on another, and you can only use it while it is overhead. Typical passes give a handful of minutes of usable time, and the exchange is usually just callsign and four-character grid square. Linear transponders such as RS-44 relay a whole slice of spectrum, so SSB and CW can share it and many stations can work at once. The ISS can offer APRS on 145.825 MHz and, when it is enabled, a cross-band FM voice repeater. QO-100 is geostationary, so there is no Doppler and no tracking, but you need a 2.4 GHz uplink and a 10 GHz downlink chain.

Treat frequencies and status as things to verify before every session. Satellites go in and out of service, change modes, run on battery limits, or get commanded differently. Check the AMSAT status pages and the current frequency tables before you plan a station around any one bird. As a rough guide, SO-50 has historically used 145.850 MHz up and 436.795 MHz down, with a CTCSS access procedure you should confirm. AO-91 and AO-92 have used 70 cm uplinks and 2 m downlinks with a 67 Hz tone. RS-44 has been an inverting linear transponder with a 70 cm uplink around 435.610–435.640 MHz and a 2 m downlink around 145.935–145.965 MHz. Check all of this against current data.

Doppler is the part that surprises people. At 435 MHz, a low-orbit satellite can shift the signal by roughly ±10 kHz over a pass. At 145 MHz the shift is about a third of that. That is small enough to catch by hand on a wide FM receiver, but not on SSB or CW. On a linear bird you want your downlink to stay where you can copy it and your uplink to track the satellite, so that your signal lands where you intend inside the passband. Many people tune the downlink by ear and let software correct the uplink. Others let the software correct both. Either way, what matters is that you decide on a routine and stick to it.

Gpredict handles tracking, pass prediction and radio control, and it talks to Hamlib for rig and rotator control. SatPC32 is a Windows program with a long history in the satellite community and strong Doppler-control support for many rigs. Either one is only as good as the element sets you feed it. Update your Keplerian data regularly, because old elements drift and your predicted pass time and Doppler curve drift with them. Set your location properly too. Your Maidenhead grid is the exchange most contacts want, and it is worth learning your six-character locator.

For antennas, the common entry point is a handheld dual-band Yagi such as the Arrow style, with a 2 m and a 70 cm element set on one boom, and an HT or two. It is portable and cheap, and it forces you to learn to point by hand. Two limits show up quickly. A single HT usually can't transmit and receive at the same time, so you can't hear yourself on the downlink without a second radio or a full-duplex rig. Also, if you point by hand while tuning and logging, something gives. A rotator removes that, but it adds cable, mast and calibration work. Elevation matters too, because low passes are mostly about horizon obstructions and ground noise rather than gain.

Polarization matters more than many beginners expect. Linear Yagis against satellites that rotate or tumble can produce fading, and circular polarization reduces it but costs more or needs more complex antennas. Don't spend months chasing gain before you have tried the basics. Start with simple setups, learn your local horizon, and add complexity only when the limits become obvious.

Questions for everyone: What setup would you recommend for a first station on a tight budget? Do you let Doppler software control the radio or do it by hand at first? And for people considering QO-100, what do you think is the real barrier to entry: the dish, the 2.4 GHz uplink, or the frequency stability of the 10 GHz receive chain?

  • Replies 2
  • Views 12
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

For a first station I'd keep it simple and separate the problems. First, learn to hear a pass. An HT and an Arrow-style antenna are enough for FM birds, and you can listen for a while before you try to transmit. That tells you where the satellite is, how Doppler sounds, and whether your horizon is clear. Then add a second receiver or a full-duplex rig so you can monitor your own downlink. Not being able to hear yourself is a more common cause of failed attempts than power or antenna choice.

On the Doppler question: for FM satellites, doing it by hand is entirely workable if you keep the downlink fixed and step the uplink. Work out a rhythm, such as a small step at acquisition, another near closest approach, and another near loss of signal, and let the 5 kHz channel steps help you. For linear birds like RS-44 the manual habit gets tiring, and a rig-control setup via Gpredict or SatPC32 pays off quickly. Test your control chain on a pass you don't intend to operate. Get the CAT cable, the radio's VFO tracking and the rotator working before you need them. And always check keps before a session, because stale elements waste whole passes.

  • Moderators

A few points on the linear side and on QO-100. On an inverting bird like RS-44 the sideband swaps between uplink and downlink, so you typically transmit USB and receive LSB, or the reverse, depending on the band arrangement. If your transmit signal appears at the wrong place in the passband, check the inversion and your tuning direction before you blame the antenna. Also don't pile on power. A transponder is shared by everybody, and a strong signal can desensitise it for others. A good rule is to adjust until your downlink is no louder than the beacon or typical stations.

For QO-100, tracking disappears but precision comes in. The narrowband transponder uses a 2.4 GHz uplink and a 10.489 GHz downlink, and the footprint covers only part of the world, so first check that your location falls inside it. The 10 GHz LNB is the usual weak point. A standard commercial LNB drifts with temperature, so many stations use a stabilised or locked unit, or correct it against the satellite's beacons. The dish gain, feed and uplink amplifier matter, but frequency stability is what decides whether SSB sounds usable. If you are curious about it but not ready, listening only costs less than a full transmit setup. It is an easy way to learn whether the satellite is worth the build.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.